Read Sharp UP-3300 (serv.man14) Service Manual online
[Default]
n = 160 (30/203 inch)
DATA = Default stamp data
[Reference]
ESC4n:
Set logo stamp
ESC0:
Print logo stamp
GS o m: Print logo stamp (select stamp No.)
[Notice]
UP-T80BP can not receive a data during writing the logo stamp data
in internal memory.
in internal memory.
UP-T80BP inform it to host by sending XOFF charater or turning off
DTR signal.
DTR signal.
When you turn off UP-T80BP or you execute Master Reset, this data
is remained. So you need not to execute it frequenfly.
is remained. So you need not to execute it frequenfly.
When this command execute, the image setting data is cleared.
No.
COMMAND
FUNCTION
CODE
20
ESC = n
Set peripheral device
<1Bh><3Dh> n
[Range]
0
à
n
à
255
[Function]
Sets the operation of the peripheral devices.
bit
Peripheral device
1/0
0
Printer
Valid/Disabled
[Default]
n = 1
No.
COMMAND
FUNCTION
CODE
21
ESC ? n
Delete user-defined
character
character
<1Bh><3Fh> n
[Range]
32
à
n
à
126
[Function]
Deletes the user-defined character for the specified code.
[Notes]
The specified code is set to the normal character.
[Reference]
ESC &: Set user-defined character
ESC %: Select user-defined character
No.
COMMAND
FUNCTION
CODE
22
ESC @
Initialize printer
<1Bh><40h>
[Function]
Initializes the printer setting data.
[Notes]
The following data are not initialized.
Macro setting data
Receive buffer data
Stamp data
Receive buffer data
Stamp data
No.
COMMAND
FUNCTION
CODE
23
ESC J n
Print and feed paper
<1Bh><4Ah>
[Range]
0
à
n
à
255
[Function]
Prints the data in the print buffer and feeds the paper for “n
×
(basic
calculation pitch)”.
No.
COMMAND
FUNCTION
CODE
24
ESC L
Select page mode
<1Bh><4Ch>
[Function]
Switches from the standard mode to the page mode.
[Notes]
This command is valid only when entered at the beginning of a line.
[Reference]
FF: Prints the page data
No.
COMMAND
FUNCTION
CODE
25
ESC Rn
Select international character
<1Bh><52h>
[Range]
0
à
n
à
10
[Function]
Selects a character set among those shown in the table below ac-
cording to the value of “n”.
cording to the value of “n”.
n
Character set
0
U.S.A.
1
France
2
Germany
3
U.K.
4
Denmark I
5
Sweden
6
Italy
7
Spain
8
Japan
9
Norway
10
Denmark II
[Notes]
If “n” is out of the range, this command is ignored.
[Default]
n = 0
No.
COMMAND
FUNCTION
CODE
26
ESC S
Select standard mode
<1Bh><53h>
[Function]
Switches from the page mode to the standard mode.
[Notes]
This command is valid only when entered at the beginning of a line.
[Reference]
ESC L: Select page mode
No.
COMMAND
FUNCTION
CODE
27
ESC V n
Set/cancel 90clockwise
rotated character printing
rotated character printing
<1Bh><56h> n
[Range]
0
à
n
à
1 48
à
n
à
49
[Function]
Sets or cancels 90° cw (clockwise) rotated character printing accord-
ing to the value of “n”.
ing to the value of “n”.
4 – 8
Click on the first or last page to see other UP-3300 (serv.man14) service manuals if exist.