Read Sharp UP-3300 (serv.man14) Service Manual online
[Range]
0
à
n
à
255
DATA: ASCII code
[Function]
Prints the mark of interrupted printing when power failure is caused
during printing.
during printing.
Sets this mark.
Performs on-line printing of this character when power failure is
caused during printing.
caused during printing.
[Default]
DATA : “=” (3Dh)
No.
COMMAND
FUNCTION
CODE
38
ESC t n
Select character code table
<1Bh><74h> n
[Range]
0
à
n
à
27
254
à
n
à
255
[Function]
Selects the character listed on page “n” of the character code table.
Page
Character type
0
PC437: U.S.A., Standard Europe
1
PC932: Japanese
2
PC850: Multilingual
3
PC860: Portuguese
4
PC863: Canadian-French
5
PC865: Nordic
6
PC869: Greece
7
PC852: Slavic
254
Original
255
Blank page
[Default]
n = 0
No.
COMMAND
FUNCTION
CODE
39
ESC v
Transmit paper detector status
<1Bh><76h>
[Function]
Transmits the status of the paper detector when the command is
executed.
executed.
The status to be transmitted is as shown below.
bit
Function
Value 0/1
0
Near-end detector
Paper is present/Paper is out
1
Not defined
2
Not defined
3
Paper end
Paper is present/Paper is out
4
Not used
Fixed to 0
5
Not defined
6
Not defined
7
Not used
Fixed to 0
[Notes]
When DTR/DSR control is selected, the status is transmitted after the
printer confirms that the host computer is ready to receive data (DSR
signal is ON). If the host computer is not ready to receive data (DSR
signal is OFF), the printer waits until the computer is ready.
printer confirms that the host computer is ready to receive data (DSR
signal is ON). If the host computer is not ready to receive data (DSR
signal is OFF), the printer waits until the computer is ready.
When XON/XOFF control is selected, one byte is transmitted without
checking if is ready to receive data.
checking if is ready to receive data.
This command is executed during receive buffer expansion. There-
fore, if there is other data in the receive buffer, some delay may be
caused between command receiving and status transmitting.
fore, if there is other data in the receive buffer, some delay may be
caused between command receiving and status transmitting.
[Reference]
DLE EOT:
Transmit status in real time
GS a:
Transmit automatic status
GS r:
Transmit status
No.
COMMAND
FUNCTION
CODE
40
ESC { n
Set/cancel upside-down
character printing
character printing
<1Bh><7Bh> n
[Range]
0
à
n
à
255
[Function]
Sets or cancels upside-down character printing.
Only the lowest bit of “n” is valid.
When bit 0 is equal to 0, upside-down character printing is can-
celed.
celed.
When bit 0 is equal to 1, upside-down character printing is set.
[Notes]
Valid only when entered at the beginning of a line.
[Default]
n = 0
No.
COMMAND
FUNCTION
CODE
41
GS ! n
Select character size
<1Dh><21h> n
[Range]
0
à
n
à
255
[Function]
Selects the character size of Normal/Double/Quadruple (Height and
Width).
Width).
bit
Function
0
Height
000 : Normal
1
001 : Double
2
011 : Quadruple
3
4
Width
000 : Normal
5
001 : Double
6
011 : Quadruple
7
[Notes]
Height represents the vertical direction; width represents the horizon-
tal direction. When 90° cw rotated character printing is set, height and
width are reversed. Double-height/double-width selected using ESC !
is disabled by this command.
tal direction. When 90° cw rotated character printing is set, height and
width are reversed. Double-height/double-width selected using ESC !
is disabled by this command.
[Default]
n = 0
[Reference]
[ESC] !: Set character mode
No.
COMMAND
FUNCTION
CODE
42
GS * n1 n2 [data]
(n1
×
n2
×
8)
Set image data
<1Dh><2Ah> ...
[Range]
1
à
n1
à
72: Horizontal size
1
à
n2
à
255: Vertical size
n1
×
n2
à
2880
0
à
data
à
255
4 – 11
Click on the first or last page to see other UP-3300 (serv.man14) service manuals if exist.