Read Panasonic KV-S7075C (serv.man2) Service Manual online
120
F38 (ASIC (Back)
SDRAM Error)
SDRAM Error)
9C xx
00 00 Access error to SDRAM
(IC1019, IC1020)
1. Check the soldering condition of the
parts surrounding the Gate Array
(IC1013).
2. Replace faulty parts or CONTROL
Board.
parts surrounding the Gate Array
(IC1013).
2. Replace faulty parts or CONTROL
Board.
F40 (Hopper error)
30 00 00 00 1. Paper Feed Motor does not
work properly.
1. Check the motor mechanism condition,
by carrying out ”Hopper Drive” test in
Sec. 9.3.6.
2. Check the following connection:
by carrying out ”Hopper Drive” test in
Sec. 9.3.6.
2. Check the following connection:
→ Paper Feed Motor to CN3026
(POWER RELAY Board)
3. Replace faulty cables.
4. Replace Paper Feed Motor.
3. Replace faulty cables.
4. Replace Paper Feed Motor.
2. Feed Motor control circuit
does not work properly.
does not work properly.
1. Check the following connections and
soldering condition on each connector:
soldering condition on each connector:
a. CN2004 (CENTER Board) to
CN4005 (DRIVE Board)
b. CN4009 (DRIVE Board) to
CN3021 (POWER RELAY Board)
2. Check the soldering condition of
IC4007 and its surrounding parts.
3. Check the following signals on the
DRIVE Board:
b. CN4009 (DRIVE Board) to
CN3021 (POWER RELAY Board)
2. Check the soldering condition of
IC4007 and its surrounding parts.
3. Check the following signals on the
DRIVE Board:
a. IC4007-1,3,4 and 5th pins
(phase signals): See Fig. 10.2.1.
b. IC4007-19th pin (VREF): 2.5 V
or less.
4. Replace faulty parts or boards.
b. IC4007-19th pin (VREF): 2.5 V
or less.
4. Replace faulty parts or boards.
3. Hopper mechanical problem
(Rotation from the Paper
Feed Motor Gear is not
transmitted to the Hopper
properly.)
(Rotation from the Paper
Feed Motor Gear is not
transmitted to the Hopper
properly.)
1. Check the Hopper mechanism
condition by carrying out "Hopper
Drive" test. (See 9.3.6.)
Note:
condition by carrying out "Hopper
Drive" test. (See 9.3.6.)
Note:
Regarding the Hopper lift drive
mechanism, see Sec. 6.3 and 6.4.
mechanism, see Sec. 6.3 and 6.4.
2. Reassemble improper lay-out or
replace faulty parts.
replace faulty parts.
4. Hopper Home Detector does
not work properly.
not work properly.
1. Execute “Key / Sensor” test in the
Sec. 9.3.6 to check the detector
condition.
2. Check whether the Interrupter plate
interrupts the detector correctly.
3. Check the following connection and
soldering condition on each connector:
Sec. 9.3.6 to check the detector
condition.
2. Check whether the Interrupter plate
interrupts the detector correctly.
3. Check the following connection and
soldering condition on each connector:
→ CN23 (HOPPER HOME DETECTOR
Board) to CN26(SESOR RELAY
Board)
4. Check HOPPER_HOME signal:
Board)
4. Check HOPPER_HOME signal:
→ CN23-3rd pin (5 V when Interrupter
plate interrupts IC3005 on the
HOPPER HOME Board.
5. Check the soldering condition of
IC2007 on the CENTER Board and
repair it.
6. Replace faulty parts and boards.
HOPPER HOME Board.
5. Check the soldering condition of
IC2007 on the CENTER Board and
repair it.
6. Replace faulty parts and boards.
Error Code
Possible Cause
Check Point
Remarks
Classification
Code
ST1 ST2 ST3 ST4
Click on the first or last page to see other KV-S7075C (serv.man2) service manuals if exist.