Read Panasonic KV-S7075C (serv.man2) Service Manual online
117
U20 (Skew Error)
19 00 00 00 1. Document on the Hopper
Tray is not set correctly.
Set the document on the Hopper Tray,
sliding the Document Guides so that they
match the document width and execute
scanning again.
sliding the Document Guides so that they
match the document width and execute
scanning again.
2. ADF Door is not closed
firmly.
firmly.
Close the door firmly.
3. A roller (Paper Feed,
Separation, DFP, Drive, Exit,
or Free) is dirty.
Separation, DFP, Drive, Exit,
or Free) is dirty.
1. Clean the roller.
2. Clear the counter for cleaning roller to
zero with the Service Utility described in
Sec. 9.
2. Clear the counter for cleaning roller to
zero with the Service Utility described in
Sec. 9.
4. A roller (Paper Feed,
Separation, DFP, Drive, or
Exit) is swollen irregularly.
Separation, DFP, Drive, or
Exit) is swollen irregularly.
1. Replace the roller.
2. After replacing Paper Feed, Separation,
and DFP Rollers, clear the counter for
replacing roller to zero with the Service
Utility described in Sec. 9.
2. After replacing Paper Feed, Separation,
and DFP Rollers, clear the counter for
replacing roller to zero with the Service
Utility described in Sec. 9.
5. Paper dust exists on or
around a Skew Sensor.
around a Skew Sensor.
Clean the sensor surface.
6. The Skew (L) Sensor does
not work properly.
not work properly.
1. Execute “Key / Sensor” test in the
Sec. 9.3.6 to check the sensor
condition.
2. Check the sensor alignment is proper.
(whether the sensor direction faces
its reflector.)
3. Check the following connections and
soldering condition on each connector:
a. CN13 (STARTING SENSOR
Board) to CN12 (SENSOR RELAY
Board)
b. CN29 (SENSOR RELAY Board) to
CN2006 (CENTER Board)
4. Check the following signal:
a. SKEW_L signal (CN2006-12th pin)
Sec. 9.3.6 to check the sensor
condition.
2. Check the sensor alignment is proper.
(whether the sensor direction faces
its reflector.)
3. Check the following connections and
soldering condition on each connector:
a. CN13 (STARTING SENSOR
Board) to CN12 (SENSOR RELAY
Board)
b. CN29 (SENSOR RELAY Board) to
CN2006 (CENTER Board)
4. Check the following signal:
a. SKEW_L signal (CN2006-12th pin)
→3.3 V (when no document exists on
the SKEW_L Sensor)
b. Check the reference signal for the
SKEW_L signal on the CENTER
Board.
b. Check the reference signal for the
SKEW_L signal on the CENTER
Board.
→ IC2027-4th pin: 3.3 V (when no
document exists)
5. Replace faulty parts or boards.
5. Replace faulty parts or boards.
7. The Skew (R) Sensor does
not work properly
not work properly
1. Execute “Key / Sensor” test in the
Sec. 9.3.6 to check the sensor
condition.
2. Check the sensor alignment is proper.
(whether the sensor direction faces its
reflector)
3. Check the following connections and
soldering condition on each connector:
a. CN13(STARTING SENSOR Board)
to CN12(SENSOR RELAY Board)
b. CN29 (SENSOR RELAY Board)
to CN2006(CENTER Board
4. Check the following signals:
Sec. 9.3.6 to check the sensor
condition.
2. Check the sensor alignment is proper.
(whether the sensor direction faces its
reflector)
3. Check the following connections and
soldering condition on each connector:
a. CN13(STARTING SENSOR Board)
to CN12(SENSOR RELAY Board)
b. CN29 (SENSOR RELAY Board)
to CN2006(CENTER Board
4. Check the following signals:
a. SKEW_R signal (CN2006-13th pin)
→ 3.3 V (when no document exists on
the SKEW_R Sensor)
b. Check the reference signal for
the SKEW_R signal on the CENTER
Board.
b. Check the reference signal for
the SKEW_R signal on the CENTER
Board.
→ IC2027-3rd pin: 3.3 V (when no
document exists)
5. Replace faulty parts or boards.
5. Replace faulty parts or boards.
Error Code
Possible Cause
Check Point
Remarks
Classification
Code
ST1 ST2 ST3 ST4
Click on the first or last page to see other KV-S7075C (serv.man2) service manuals if exist.