Read Panasonic KV-S7075C (serv.man2) Service Manual online
116
U16 (Exit Jam1:
Paper did not pass
through the Ending
Paper did not pass
through the Ending
Sensor)
16 00 00 00 1. Document remains forward
Ending Sensor.
Remove the document from the scanner.
2. Paper dust exists on or
around the Ending Sensor.
around the Ending Sensor.
1. Blow off the dust with the included
accessory blower. (See Sec.7.2.)
2. Execute "Key / Sensor" and "Sensor
Sensitive Level" tests in Sec.9.3.6 to
check the sensor condition.
accessory blower. (See Sec.7.2.)
2. Execute "Key / Sensor" and "Sensor
Sensitive Level" tests in Sec.9.3.6 to
check the sensor condition.
3. Mechanical problem (Exit
Roller, Drive Belt,
Conveyor)
Roller, Drive Belt,
Conveyor)
1. Execute “Conveyor Motor” test in
Sec.9.3.6 to check the mechanical
condition.
2. Check whether the Drive Rollers (3, 4),
Exit Roller, Drive Belt, and the
conveyor to support the rollers are
assembled properly in the scanner.
3. Check the surfaces of the Drive Rollers
(3, 4), and of the Exit Roller.
a. Configuration:
Are the rollers swollen irregularly?
Sec.9.3.6 to check the mechanical
condition.
2. Check whether the Drive Rollers (3, 4),
Exit Roller, Drive Belt, and the
conveyor to support the rollers are
assembled properly in the scanner.
3. Check the surfaces of the Drive Rollers
(3, 4), and of the Exit Roller.
a. Configuration:
Are the rollers swollen irregularly?
→ Replace the rollers.
b. Whether the roller surfaces are
dirty
dirty
→ Clean the surfaces
4. Check whether the Drive Belt tension
is proper.
is proper.
→ Re-adjust the belt tension.
U18 (Paper remains
in the scanner)
in the scanner)
18
xx
00 00 1. Document remains in the
scanner.
Remove the document from the scanner.
2. Paper dust exists on a
sensor.
sensor.
1. Execute “Key / Sensor” and “Sensor
Sensitive Level” tests in Sec. 9.3.6 to
define the sensor that results in this
problem.
2. Blow off the dust on the surface of the
sensor with the included accessory
blower. (See Sec.7.2.)
Sensitive Level” tests in Sec. 9.3.6 to
define the sensor that results in this
problem.
2. Blow off the dust on the surface of the
sensor with the included accessory
blower. (See Sec.7.2.)
3. A sensor does not work
correctly.
correctly.
1. Execute “Key / Sensor” and “Sensor
Sensitive Level” tests in Sec. 9.3.6 to
define the sensor that occurs this
problem.
2. Check each sensor, its connection, and
its monitor circuits.
a. Waiting Sensor
Sensitive Level” tests in Sec. 9.3.6 to
define the sensor that occurs this
problem.
2. Check each sensor, its connection, and
its monitor circuits.
a. Waiting Sensor
→ See the 5th item of “U11”.
b. Starting Sensor
→ See the 3rd item of “U12”.
c. Skew (L) or Skew (R) Sensor
→ See the 6th and 7th item of “U20”.
d. ENDING Sensor
→ See the 3rd item of “U14”.
Error Code
Possible Cause
Check Point
Remarks
Classification
Code
ST1 ST2 ST3 ST4
Click on the first or last page to see other KV-S7075C (serv.man2) service manuals if exist.