Read Panasonic KV-S7075C (serv.man2) Service Manual online
119
U30 (Cover open.)
20 00 00 00 1. ADF or EXIT Door is not
closed enough.
Shut the door properly.
2. Door SW (Micro switch: Exit
Door or ADF Door Switch)
does not work correctly.
Door or ADF Door Switch)
does not work correctly.
1. Execute “Key / Sensor” in Sec. 9.3.6
to check the door switch (Exit, ADF)
ON/OFF condition.
2. Check the condition between the Door
Switch and CN3027 on POWER
RELAY Board.
3. Check the Door Switch mechanical
condition.
4. Replace a faulty cable.
5. Replace the Door Switch.
to check the door switch (Exit, ADF)
ON/OFF condition.
2. Check the condition between the Door
Switch and CN3027 on POWER
RELAY Board.
3. Check the Door Switch mechanical
condition.
4. Replace a faulty cable.
5. Replace the Door Switch.
3. Monitor circuit to check the
door ON / OFF condition is
broken.
door ON / OFF condition is
broken.
1. Execute “Key / Sensor” in Sec. 9.3.6
to check the door switch ON/OFF
condition.
2. Check 24VSLP signal. (CN3022-1st
pin on POWER RELAY Board): +24 V
(when door is closed)
3. Check DOOR signal (CN4005-31st)
+5 V (when the door is open)
0 V (when the door is closed)
4. Replace a faulty cable.
5. Replace POWER RELAY Board
6. Replace DRIVE Board or CONTROL
Board.
to check the door switch ON/OFF
condition.
2. Check 24VSLP signal. (CN3022-1st
pin on POWER RELAY Board): +24 V
(when door is closed)
3. Check DOOR signal (CN4005-31st)
+5 V (when the door is open)
0 V (when the door is closed)
4. Replace a faulty cable.
5. Replace POWER RELAY Board
6. Replace DRIVE Board or CONTROL
Board.
F17 (SD-RAM error) 87
xx
xx
00 Access error to SDRAM
(IC1015 to IC1020) on the
CONTROL Board
CONTROL Board
1. Check the soldering condition of the
SDRAM (IC1015 to IC1020).
2. Replace faulty parts or CONTROL
Board.
SDRAM (IC1015 to IC1020).
2. Replace faulty parts or CONTROL
Board.
F18 (Extension SD-
RAM error)
RAM error)
88
xx
00 00 Access error to an additional
SDRAM attached to CN1005
and CN1006
and CN1006
1. Check whether the additional SDRAM
is attached to CN1005 and CN1006
properly. Or reattached it.
2. Check the SDRAM specifications.
3. Check the soldering condition of the
CN1005 and CN1006 (for the SDRAM)
and its surrounding circuits on the
CONTROL Board to repair it.
4. Replace faulty parts or CONTROL
Board.
is attached to CN1005 and CN1006
properly. Or reattached it.
2. Check the SDRAM specifications.
3. Check the soldering condition of the
CN1005 and CN1006 (for the SDRAM)
and its surrounding circuits on the
CONTROL Board to repair it.
4. Replace faulty parts or CONTROL
Board.
F31 (Analog IC
error)
error)
95 00 00 00 Access error to Analogue IC
1. Check the following connections and
soldering condition to repair it:
soldering condition to repair it:
→ IC2009 to IC2016 (CENTER Board)
and their surround circuits
2. Replace faulty parts or boards.
2. Replace faulty parts or boards.
F33 (USB IC error)
97 00 00 00 Access error to USB Controller 1. Check the soldering condition of the
USB Controller (IC1021) and its
surrounding circuits on the CONTROL
Board to repair it.
2. Replace faulty parts or CONTROL
Board.
surrounding circuits on the CONTROL
Board to repair it.
2. Replace faulty parts or CONTROL
Board.
F34 (EEPROM
error)
error)
98 00 00 00 Access error to EEPROM
1. Check the soldering condition of the
EEPROM (IC1003) and its surrounding
circuits on the CONTROL Board.
2. Replace faulty parts or CONTROL
Board.
EEPROM (IC1003) and its surrounding
circuits on the CONTROL Board.
2. Replace faulty parts or CONTROL
Board.
F36 (ASIC (Front)
SDRAM Error)
SDRAM Error)
9A xx
00 00 Access error to SDRAM
(IC1015 to IC1018)
1. Check the soldering condition of the
parts surrounding the Gate Array
(IC1011).
2. Replace faulty parts or CONTROL
Board.
parts surrounding the Gate Array
(IC1011).
2. Replace faulty parts or CONTROL
Board.
Error Code
Possible Cause
Check Point
Remarks
Classification
Code
ST1 ST2 ST3 ST4
Click on the first or last page to see other KV-S7075C (serv.man2) service manuals if exist.