Read Panasonic KV-S7075C (serv.man2) Service Manual online
115
U14 (Conveyor
Jam3: Paper did not
reach the Ending
Sensor.
Jam3: Paper did not
reach the Ending
Sensor.
14 00 00 00 1. Document remains between
Starting Sensor and Ending
Sensor.
Sensor.
Remove the document from the scanner.
2. Paper dust exists on or
around the Ending Sensor.
around the Ending Sensor.
1. Blow off the dust with the included
accessory blower. (See Sec.7.)
2. Execute "Key / Sensor" and "Sensor
Sensitive Level" tests in Sec.9.3.6 to
check the sensor condition.
accessory blower. (See Sec.7.)
2. Execute "Key / Sensor" and "Sensor
Sensitive Level" tests in Sec.9.3.6 to
check the sensor condition.
3. ENDING Sensor does not
work correctly.
work correctly.
1. Execute “Key / Sensor” test in the
Sec. 9.3.6 to check the sensor condition.
2. Check the sensor alignment is proper
(whether the sensor direction faces to its
reflector.)
3. Check the following connections and
soldering condition on each connector:
a. CN22 (ENDING SENSOR Board) to
CN11 (SENSOR RELAY Board)
b. CN29 (SENSOR RELAY Board) to
CN2006 (CENTER Board)
4. Check the following signals:
a. PEXIT signal (CN11-2nd or CN29-
7th pin)
Sec. 9.3.6 to check the sensor condition.
2. Check the sensor alignment is proper
(whether the sensor direction faces to its
reflector.)
3. Check the following connections and
soldering condition on each connector:
a. CN22 (ENDING SENSOR Board) to
CN11 (SENSOR RELAY Board)
b. CN29 (SENSOR RELAY Board) to
CN2006 (CENTER Board)
4. Check the following signals:
a. PEXIT signal (CN11-2nd or CN29-
7th pin)
→ 0 V (when none exists on the
Ending Sensor)
b. Check the reference signal for the
PEXIT signal on the CENTER Board.
IC2021-2nd pin: 1.5 V or less
IC2021-3rd pin: Approx. 1.5 V
c. Check comparator output signal.
b. Check the reference signal for the
PEXIT signal on the CENTER Board.
IC2021-2nd pin: 1.5 V or less
IC2021-3rd pin: Approx. 1.5 V
c. Check comparator output signal.
→ IC2024-1st pin: 3.3 V (when no
document exists)
5. Replace faulty parts or cables.
5. Replace faulty parts or cables.
4. Mechanical problem (Drive
Rollers, Drive Belt,
Conveyor)
Rollers, Drive Belt,
Conveyor)
1. Execute "Conveyor Motor" test in
Sec.9.3.6 to check the mechanical
condition.
2. Check whether the Drive Rollers(3, 4),
Drive Belt, and the conveyor to
support the Drive Rollers are
assembled properly in the scanner.
3. Check the surfaces of the Drive Rollers
(3, 4
Sec.9.3.6 to check the mechanical
condition.
2. Check whether the Drive Rollers(3, 4),
Drive Belt, and the conveyor to
support the Drive Rollers are
assembled properly in the scanner.
3. Check the surfaces of the Drive Rollers
(3, 4
).
a. Configuration:
Are the rollers swollen irregularly?
Are the rollers swollen irregularly?
→ Replace the rollers.
b. Whether the roller surfaces are
dirty
dirty
→ Clean the surfaces.
4. Check whether the Drive Belt tension is
proper.
proper.
Error Code
Possible Cause
Check Point
Remarks
Classification
Code
ST1 ST2 ST3 ST4
Click on the first or last page to see other KV-S7075C (serv.man2) service manuals if exist.