Read Panasonic KV-S7075C (serv.man2) Service Manual online
113
U12 (Conveyor
Jam1: Paper did not
reach the Starting
Sensor.)
Jam1: Paper did not
reach the Starting
Sensor.)
12 00 00 00 1. Document remains between
Waiting Sensor and Starting
Sensor.
Sensor.
Remove the document from the scanner.
2. Paper dust exists on or
around the Starting Sensor.
around the Starting Sensor.
1. Blow off the dust with the included
accessory blower. (See Sec.7.)
2. Execute "Key / Sensor" and "Sensor
Sensitive Level" tests in Sec.9.3.6 to
check the sensor condition.
accessory blower. (See Sec.7.)
2. Execute "Key / Sensor" and "Sensor
Sensitive Level" tests in Sec.9.3.6 to
check the sensor condition.
3. Starting Sensor does not
work correctly.
work correctly.
1. Execute "Key / Sensor" test in the
Sec. 9.3.6 to check the sensor condition.
2. Check the sensor alignment is proper.
(whether the sensor direction faces to its
reflector)
3. Check the following connections and
soldering condition on each connector:
Sec. 9.3.6 to check the sensor condition.
2. Check the sensor alignment is proper.
(whether the sensor direction faces to its
reflector)
3. Check the following connections and
soldering condition on each connector:
a. CN13 (STARTING SENSOR
Board) to CN12 (SENSOR RELAY
Board)
b. CN29 (SENSOR RELAY Board)
to CN2006 (CENTER Board)
4. Check the following signals:
a. STARTING signal (CN13-3rd pin,
CN29-10th pin)
Board)
b. CN29 (SENSOR RELAY Board)
to CN2006 (CENTER Board)
4. Check the following signals:
a. STARTING signal (CN13-3rd pin,
CN29-10th pin)
→ 0 V (when none exists on the
Starting Sensor)
b. Check the reference signal for the
PHEAD signal on the CENTER
Board.
IC2019-6th pin: 1.5 V or less
IC2019-5th pin: Approx. 1.5 V
c. Check comparator output signal.
b. Check the reference signal for the
PHEAD signal on the CENTER
Board.
IC2019-6th pin: 1.5 V or less
IC2019-5th pin: Approx. 1.5 V
c. Check comparator output signal.
→ IC2022-7th pin: 3.3 V (when no
document exists)
5. Replace faulty parts or boards.
5. Replace faulty parts or boards.
4. Mechanical problem (Drive
Roller, Drive Belt, Conveyor)
Roller, Drive Belt, Conveyor)
1. Execute "Feed Motor" and "Conveyor
Motor" tests in Sec. 9.3.6 to check the
mechanical condition.
2. Check whether the Drive Rollers1, 2,
the Drive belt, and the conveyor to
support the Drive Rollers are
assembled properly in the scanner.
3. Check the surfaces of the Drive Rollers
a. Configuration:
Are the rollers swollen irregularly?
Motor" tests in Sec. 9.3.6 to check the
mechanical condition.
2. Check whether the Drive Rollers1, 2,
the Drive belt, and the conveyor to
support the Drive Rollers are
assembled properly in the scanner.
3. Check the surfaces of the Drive Rollers
a. Configuration:
Are the rollers swollen irregularly?
→ Replace the rollers.
b. Whether the roller surfaces are dirty
→ Clean the surfaces.
4. Check whether the Drive Belt tension is
proper.
proper.
→
Re-adjust the belt tension.
5. Conveyor Motor does not
work properly.
work properly.
1. Check the motor mechanism condition
by carrying out "Conveyor Motor" test.
(See 9.3.6.)
2. Check the following connections and
soldering condition on each connector:
by carrying out "Conveyor Motor" test.
(See 9.3.6.)
2. Check the following connections and
soldering condition on each connector:
a. Conveyor Motor to CN3025
(POWER RELAY Board)
b. CN3021 (POWER RELAY Board)
to CN4009 (DRIVE Board)
3. Check the following signals on the
DRIVE Board:
to CN4009 (DRIVE Board)
3. Check the following signals on the
DRIVE Board:
→ CN4009-3, 5, 6, and 8th pins:
See Fig. 10.2.3.
4. Replace faulty cables.
5. Replace Conveyor Motor.
4. Replace faulty cables.
5. Replace Conveyor Motor.
Error Code
Possible Cause
Check Point
Remarks
Classification
Code
ST1 ST2 ST3 ST4
Click on the first or last page to see other KV-S7075C (serv.man2) service manuals if exist.