Read Panasonic KV-S7065C (serv.man2) Service Manual Supplement online
10
4.3.
“Section 9.3 Operation”
This section describes each operation (or status indication), according to the function item list shown in Sec.9.2.
4.3.1.
“Section 9.3.1 Scanner Status”
This function indicates scanner status, updating it every few seconds.
The status messages and its contents are as follows.
The status messages and its contents are as follows.
Fig. 9.3.1 Scanner Status
Classified Code
Status Message
Contents
—
Scanner has no error.
No error
U11, U12, U14,
U16
U16
A paper jam has occurred.
Open the scanner’s door, remove the
documents, and close the cover.
Place the documents back in the document
feed tray.
Open the scanner’s door, remove the
documents, and close the cover.
Place the documents back in the document
feed tray.
U11: Paper feed Jam
U12: Conveyor jam1 (around Conveyor)
U13: Conveyor jam2 (around Conveyor)
U16: Exit jam (around Exit Roller)
Note: Refer to Section 10.2 (Troubleshooting)
U12: Conveyor jam1 (around Conveyor)
U13: Conveyor jam2 (around Conveyor)
U16: Exit jam (around Exit Roller)
Note: Refer to Section 10.2 (Troubleshooting)
in the Service Manual
(Order No.: KM70401905C0) when performing
troubleshooting for the above error codes.
U18
Paper remains in the scanner.
Open the scanner’s door, remove the
documents, and close the cover.
Place the documents back in the document
feed tray.
Open the scanner’s door, remove the
documents, and close the cover.
Place the documents back in the document
feed tray.
Document remains in the scanner, or dust is
attached around a sensor.
attached around a sensor.
U20
A skew error has occurred.
Open the scanner’s door, remove the
documents, and close the cover.
Place the documents back in the document
feed tray.
Open the scanner’s door, remove the
documents, and close the cover.
Place the documents back in the document
feed tray.
Skew error
U23
A paper double feed has occurred.
Open the scanner’s door, remove the
documents, and close the cover.
Place the documents back in the document
feed tray.
Open the scanner’s door, remove the
documents, and close the cover.
Place the documents back in the document
feed tray.
Double feed error
U30
Scanner Door is open! Please close the door.
Door is open.
Fxx
System error occurred!
Please consult with a service representative.
Please consult with a service representative.
Service level error occurred.
—
*** Warning***
The rollers need to be cleaned.
Please clean the rollers. Please select Clear Counter
button after cleaning rollers.
The rollers need to be cleaned.
Please clean the rollers. Please select Clear Counter
button after cleaning rollers.
Warning for cleaning rollers.
—
***Warning***
The replaceable rollers (consumable) are
close to reaching their usable life.
To insure reliable operation, please
replace these rollers with Roller Exchange
Kit for your specific scanner.
After replacing the rollers, select the
“Clear Counter” button.
The replaceable rollers (consumable) are
close to reaching their usable life.
To insure reliable operation, please
replace these rollers with Roller Exchange
Kit for your specific scanner.
After replacing the rollers, select the
“Clear Counter” button.
Warning for replacing rollers.
—
***Warning***
Insufficient front light error occurred.
The lamp and/or scanning sensor need to be replaced.
Insufficient front light error occurred.
The lamp and/or scanning sensor need to be replaced.
1. The lamp have reached its life expectancy.
2. Lamp drive circuit for the front does not work
properly.
2. Lamp drive circuit for the front does not work
properly.
—
***Warning***
Insufficient back light error occurred.
The lamp and/or scanning sensor need to be replaced.
Insufficient back light error occurred.
The lamp and/or scanning sensor need to be replaced.
1. The lamp have reached its life expectancy.
2. Lamp drive circuit for the back does not work
properly.
2. Lamp drive circuit for the back does not work
properly.
—
***Warning***
The front reference plate may need to be cleaned.
Please clean the front reference plate.
The front reference plate may need to be cleaned.
Please clean the front reference plate.
The surface of the plate is dirty.
—
***Warning***
The back reference plate may need to be cleaned.
Please clean the back reference plate.
The back reference plate may need to be cleaned.
Please clean the back reference plate.
The surface of the plate is dirty.
—
Scanner is not connected!
Scanner is not connected to PC properly.
Click on the first or last page to see other KV-S7065C (serv.man2) service manuals if exist.