Read Panasonic KV-S7065C (serv.man2) Service Manual Supplement online
8
4.2.
“Section 9.2 Function item list of Service Utility”
Service Utility item list is as follows.
Note:
When two or more scanners are connected to PC, execute “Select Scanner” to define the scanner before evaluating.
The procedure is as follows.
Note:
When two or more scanners are connected to PC, execute “Select Scanner” to define the scanner before evaluating.
The procedure is as follows.
1. Click “Select Scanner” on the Main Menu.
2. Select the product number and interface of the scanner to evaluate.
2. Select the product number and interface of the scanner to evaluate.
Item
Purpose
Remarks
Scanner Status
To indicate scanner status (Ready, Error, or Warning)
(2)
Scanner Information
To indicate scanner information about Model, firmware version,
Gate Array version, board revision, additional memory size
(status), and interface condition
Gate Array version, board revision, additional memory size
(status), and interface condition
(2)
Scanner Counter Update All
Counters
To update the values of System Counter, Flatbed Counter,
Cleaning roller Counter, and Replacing roller Counter
Cleaning roller Counter, and Replacing roller Counter
(1), (6)
Clear Counter for
cleaning roller
cleaning roller
To clear Counter for cleaning roller to zero after cleaning roller
(1), (6)
Clear Counter for
replacing roller
replacing roller
To clear Counter for replacing roller to zero after replacing roller
(1), (6)
Scanner Condition Sleep Mode
To set “Waiting Time” before entering to the sleep
mode
mode
(
1)
*1
Clean Imprinter
To clean an ink jet head of imprinter
(1), (6)
Paper Mode / Buzzer
Setting
Setting
To set scanning size (A4 or Letter) when the Document Guide is
in A4 position, and to set Buzzer ON/OFF condition.
in A4 position, and to set Buzzer ON/OFF condition.
(
1)
Compatible Mode
To make this scanner operate as another scanner with this mode (1), (3)
User Shading
To execute shading correction at the user side, or to restore the
shading data to the default (Factory-setting)
shading data to the default (Factory-setting)
(4)
Warning Setting
To set warning timing to clean roller and to replace roller
(3)
Set Default
To set “sleep mode setting“, “warning timing to clean
and to replace roller”, and “feed speed” to the default
and to replace roller”, and “feed speed” to the default
(3)
Test
LED
To light LED on the front panel with colors changing periodically
(Green
→
Orange
→
Red
→
Green
→
Orange......)
(5)
Key / Sensor
To do Key or Sensor ON / OFF test
(5)
Sensor Sensitive Level
To check sensitive level of each sensor (Waiting, Starting, Skew
(L), Skew (R), Ending)
(L), Skew (R), Ending)
(5)
Feed Motor
To check Paper Feed Motor’s Rotating
(5)
Conveyor Motor
To check Conveyor Motor’s Rotating
(5)
Hopper Drive
To check the hopper’s Up/Down Mechanism
(5)
Feed
To check paper feed condition
(5)
Sleep Mode
To check whether sleep mode function works properly
(5)
CIS Level
To check maximum peak level after setting gain
(5)
CIS Focus
To monitor the image output level, generated within
the effective Pixel Width of CIS
the effective Pixel Width of CIS
(5)
Double Feed
To check the Double Feed Detector (R)’s level (Response
level) after setting the ultrasonic sending level and frequency
of the Double Feed Detector (G)
level) after setting the ultrasonic sending level and frequency
of the Double Feed Detector (G)
(5)
Memory
To execute memory R/W test
(5)
Adjust
Shading
To execute shading correction
(4)
All Position
To adjust scanning length, vertical, and horizontal positions
for front and back sides, flatbed automatically
for front and back sides, flatbed automatically
(4)
Individual Position
1. To execute automatic length, vertical or horizontal position
adjustment for front and back sides, flatbed individually
2. To adjust scanning length, vertical and horizontal positions
for front and back sides, flatbed manually
adjustment for front and back sides, flatbed individually
2. To adjust scanning length, vertical and horizontal positions
for front and back sides, flatbed manually
(4)
Double Feed
To correct the Double Feed detector’s ultrasonic sending
level and frequency automatically or manually
level and frequency automatically or manually
(4)
USB ID
To set a USB ID for the scanner, connected to PC
(3)
*2
Feed Speed
To change the paper feed speed
(4)
Other (USB ID.
Save Information)
Save Information
To save scanner and PC information
(1)
Click on the first or last page to see other KV-S7065C (serv.man2) service manuals if exist.