Read Panasonic KV-S3105C / KV-S3085 (serv.man3) Service Manual online
10.3. Requirement after parts replacement
Following adjustments are required when print circuit board or part is replaced.
Replaced print circuit board or part
Required adjustment
CONTROL Board
Adjust Shading
Adjust All Position & Length automatically
Adjust Double Feed Detector Gain
Initialize EEPROM. (See 9.6.)
Set USB ID. (See 9.7.)
Adjust All Position & Length automatically
Adjust Double Feed Detector Gain
Initialize EEPROM. (See 9.6.)
Set USB ID. (See 9.7.)
Flash ROM (It isn’t Service parts.)
Adjust Shading
Front side optical unit or front side lamp
Adjust Shading
Adjust All Position & Length automatically or the following two Adjustments should be done.
(1) Adjust Front H.Position automatically
(2) Adjust Front V.Position automatically
*When “Adjust All Position & Length automatically” is done, Length, Back H.Position, and Back V.
Position are adjusted again.
Adjust All Position & Length automatically or the following two Adjustments should be done.
(1) Adjust Front H.Position automatically
(2) Adjust Front V.Position automatically
*When “Adjust All Position & Length automatically” is done, Length, Back H.Position, and Back V.
Position are adjusted again.
Back side optical unit or back side lamp
Adjust Shading
Adjust All Position & Length automatically or 2 Adjustments should be done.
(1) Adjust Back H.Position automatically
(2) Adjust Back V.Position automatically
*When “Adjust All Position & Length automatically” is done, Length, Front H.Position, and Front
V. Position are adjusted again.
Adjust All Position & Length automatically or 2 Adjustments should be done.
(1) Adjust Back H.Position automatically
(2) Adjust Back V.Position automatically
*When “Adjust All Position & Length automatically” is done, Length, Front H.Position, and Front
V. Position are adjusted again.
Front & Back side optical units or Front &
Back side lamps
Back side lamps
Adjust Shading
Adjust All Position & Length automatically or 4 Adjustments should be done.
(1) Adjust Front H.Position automatically
(2) Adjust Front V.Position automatically
(3) Adjust Back H.Position automatically
(4) Adjust Back V.Position automatically
*When “Adjust All Position & Length automatically” is done, Length is adjusted again.
Adjust All Position & Length automatically or 4 Adjustments should be done.
(1) Adjust Front H.Position automatically
(2) Adjust Front V.Position automatically
(3) Adjust Back H.Position automatically
(4) Adjust Back V.Position automatically
*When “Adjust All Position & Length automatically” is done, Length is adjusted again.
SKEW [L] Board
Adjust All Position & Length automatically or 2 Adjustments should be done.
(1) Adjust Front H.Position automatically
(2) Adjust Back V.Position automatically
(1) Adjust Front H.Position automatically
(2) Adjust Back V.Position automatically
Double Feed Detector [Generate] or
Double Feed Detector [Receive]
Double Feed Detector [Receive]
Adjust Double Feed Detector
Initialize EEPROM (It isn’t Service Parts.) *1
· Adjust All Position & Length automatically
· Adjust Double Feed Detector
· Adjust Double Feed Detector
Disassemble and assemble which influence
to scanning positions.
EX)
Disassemble and assemble of Sub Chassis
(R), (L), Main Chassis (R), (L)
to scanning positions.
EX)
Disassemble and assemble of Sub Chassis
(R), (L), Main Chassis (R), (L)
Adjust All Position & Length automatically or 4 Adjustments should be done.
(1) Adjust Front H.Position automatically
(2) Adjust Front V.Position automatically
(3) Adjust Back H.Position automatically
(4) Adjust Back V.Position automatically
*When “Adjust All Position & Length automatically” is done, Length is adjusted again.
(1) Adjust Front H.Position automatically
(2) Adjust Front V.Position automatically
(3) Adjust Back H.Position automatically
(4) Adjust Back V.Position automatically
*When “Adjust All Position & Length automatically” is done, Length is adjusted again.
Drive Roller
Conveyor Roller
Conveyor Roller
Adjust All Position & Length automatically or the following Adjustment should be done.
(1) Adjust Length automatically
(1) Adjust Length automatically
Note
*1
: Only perform “Init. EEPROM” when EEPROM Error (F34) occurs.
When “Init. EEPROM” is executed, all adjustments in Service Mode 1 and Service Mode 2 need to be confirmed.
118
KV-S3105CSERIES / KV-S3085SERIES
Click on the first or last page to see other KV-S3105C / KV-S3085 (serv.man3) service manuals if exist.