GP-MF622E, GP-MF130E - Panasonic Video Monitoring Service Manual (repair manual). Page 2

GP MF622E/GP MF130E

This service information is designed for experienced repair technicians only and is not designed for use by the
general public.
It does not contain warnings or cautions to advise non-technical individuals of potential dangers in attempting to
service a product.
Products powered by electricity should be serviced or repaired only by experienced professional technicians. Any
attempt to service or repair the product or products dealt with in this service information by anyone else could
result in serious injury or death.

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK, 
DO NOT REMOVE COVER (OR BACK). NO USER 
SERVICEABLE PARTS INSIDE.
REFER SERVICEING TO QUALIFIED SERVICE
PERSONNEL.

This  symbol  warns  the  user  that  uninsuland  voltage 
within the  unit  may  have  sufficient  magnitude  to  cause   
electric
shock. Therefore,  it  is dangerous to make any kind of 
contact with any inside part of this unit.

This symbol alerts the user that impotant literature concerning 
the operation and maintenance of this has been included.
Therefore,  it  should  be  read  carefully  in  order  to avoid 

T

here are special components used in this equipment which are important for safety. These parts are indicated 

by the    mark  on  the  schematic diagram and  the replacement parts list. It is essential that these critical 

parts should be replaced with manufacturer's specified parts to prevent X-radiation, shock, fire, or other hazards.

Do not modify the original design without permission of manufacture.

Pick-up Device :

Inter Line Transfer type CCD with 752 (H) x 582 (V) pixels.

Image Size :

1/3” (6.00 (H) x 4.96 (V) mm)
2 : 1 interlace 1-line interlace (Frame accumulation)
2 : 1 interlace 2-line interlace (Field accumulation)

Synchronization :

Internal or External (Selectable Automatically)
Internal : Built-in sync generator
External : 4.0 V[p-p]/75 

Ω

Horizontal drive and Vertical drive pulses

for 2 : 1 interlace

External Reset :

External signal (4.0 V[p-p]/75 

Ω

, negative) supplied to EXT VD IN connector can be used as reset signal

Horizontal Resolution : 

560 lines at center

Minimum Illumination : 

1.0 lx (0.1 foot-candles), (F1.4, Manual Gain Max (+6 dB), 

γ

OFF, 2 : 1 interlace, without shutter)

Signal to Noise Ratio:

54 dB Typical (Manual Gain OFF (0 dB),  

γ

OFF, 2:1 interlace without shutter)

Gamma :

1.0

Gain Selection :

0 - 6 dB (Adjustable by Manual Gain Control on rear panel)

Electronic Shutter :

10-step (1/120 s to 1/96 000 s)

Lens Mount :

C-Mount

Vibration Resistance :

10 G (10 Hz - 150 Hz) (2 hours each for three axes)

Shock Resistance :

80 G (IEC 68) *IEC=International Electronical Technical Commission

Power Source :

DC + 12 V, 170 mA

Ambient Temperature :

−

10˚C - +50˚C (14˚F - 122˚F)

Dimensions :

29(W) x 29(H) x 65(D) mm [1-1/8”(W) x 1-1/8”(H) x 2-13/16”(D)]

Weight :

86 

g

(0.19 lbs.) (Camera Only)

Dimensions and weight indicated are approximate values.
Specifications are subject to change without notice.

Camera Cable

GP-CA34
GP-CA33
GP-CA59
GP-CA60