Read JBL ESC 360 (serv.man2) User Guide / Operation Manual online
ENGLISH
-14-
If there is no sound from any
of the speakers:
• Make sure the subwoofer is
of the speakers:
• Make sure the subwoofer is
plugged into an active AC
wall outlet.
wall outlet.
• Make sure the Master Power
Switch, located on the rear
of the subwoofer, is in the
On/Standby position.
of the subwoofer, is in the
On/Standby position.
• Make sure there is a source –
for example, a DVD Player, CD
Player, VCR or television –
hooked up to one of the four
input jacks.
Player, VCR or television –
hooked up to one of the four
input jacks.
• Make sure that the program
material is playing.
• Recheck the hookup
connections, referring to the
Speaker Connections section.
Speaker Connections section.
If there is no sound from the
surround speakers or
sound is very low:
• Check all connections
surround speakers or
sound is very low:
• Check all connections
between processor/amplifier
and each of the speakers.
and each of the speakers.
• Raise the surround volume
from the remote control (see
Operation section).
Operation section).
• Make sure the TV show or
movie you are watching is
recorded in surround, try the
Phantom or Simulated Sur-
round mode.
recorded in surround, try the
Phantom or Simulated Sur-
round mode.
• Increase the surround-
speakers’ level, using the
level-adjustment instructions
found earlier in this manual.
level-adjustment instructions
found earlier in this manual.
If there is no sound from the
center speaker:
• Make sure that the processor
center speaker:
• Make sure that the processor
is in the Surround or
3-Stereo mode. If it is in
Phantom or Stereo mode, the
center speaker will not play.
3-Stereo mode. If it is in
Phantom or Stereo mode, the
center speaker will not play.
• Increase the level of the
center channel, using the
level-adjustment instructions
earlier in this manual.
level-adjustment instructions
earlier in this manual.
• Check the connections
between the subwoofer and
the center speaker.
the center speaker.
If you have low bass output:
• Experiment with placement
• Experiment with placement
of the subwoofer. Remember,
place the subwoofer in a
corner to get maximum bass
output from the system.
place the subwoofer in a
corner to get maximum bass
output from the system.
• Increase the subwoofer level,
using the level-adjustment
instructions found earlier in
this manual.
instructions found earlier in
this manual.
• Increase the level of bass,
using the remote control.
Troubleshooting
Specifications
ESC 360 System
Power Output
Satellites:
25 Watts x 5 @ 0.1% THD
Subwoofer:
60 Watts x 1 @ 1% THD
Satellites:
25 Watts x 5 @ 0.1% THD
Subwoofer:
60 Watts x 1 @ 1% THD
Signal-to-Noise Ratio
80 dBA
80 dBA
Input Impedance
(analog inputs)
20k Ohms
(analog inputs)
20k Ohms
Input Sensitivity
(analog inputs)
400mV
(analog inputs)
400mV
Auto Turn-On Sensitivity
(analog inputs)
2mV
(analog inputs)
2mV
Frequency Response (–6 dB)
35Hz – 20kHz
35Hz – 20kHz
Dimensions (H x W x D)
Satellites (each):
111 x 81 x 92mm
Subwoofer:
315 x 300 x 310mm
Satellites (each):
111 x 81 x 92mm
Subwoofer:
315 x 300 x 310mm
Occasional refinements may
be made to existing products
without notice, but will always
meet or exceed original speci-
fications unless otherwise
stated.
be made to existing products
without notice, but will always
meet or exceed original speci-
fications unless otherwise
stated.
