AVR 35 (serv.man4) - Harman Kardon Audio User Guide / Operation Manual. Page 15

Remote Control Functions

13

o

This button does

not function with the AVR35RDS, but
it may be used when the remote is
used to control other products.

p

This button does

not function with the AVR35RDS, but
it is available for use with other
devices.

q

Press this

button to enter a radio station into the
AVR35RDS’s preset memory. After
pressing the button the MEMORY
indicator 

N will flash, and you then

have five seconds to enter a present
memory location using the 

n. (See page 26 for more

information.)

r

Press this button

when the tuner is in use to select
between automatic tuning and
manual tuning. When the button is
pressed so that the AUTO indicator 

O

goes out, pressing the 

buttons 

v will move the frequency

up or down in single-step
increments. When the FM band is in 
use, pressing this button when a
station’s signal is weak will change to
monaural reception, as indicated by
the MONO indicator 

Q. (See page 26

for more information.)

s

Press this button to

select a radio station by entering its
frequency using the 

n. (See page 26 for more
information.) This button is also used
as part of the process of erasing
command functions that have been
programmed into the remote. (See
page 31 for more information.)

t

This button is used

to operate or program the tuners
RDS functions (See page 27 for more
information).

u

When the tuner

is in use, these buttons scroll through
the stations that have been
programmed into the AVR35RDS’s
memory. When many source devices,
such as CD players, VCRs and
cassette decks, are selected using
the 

c,

these buttons will normally function as
chapter step or track advance.

v

When the

tuner is in use, these buttons will tune
up or down through the selected
frequency band. If the 

button 

r has been pressed so that

the AUTO indicator 

O is illuminated,

pressing these buttons will cause the
tuner to seek the next station with
acceptable signal strength for quality
reception. When the AUTO indicator
O is NOT illuminated, pressing these
buttons will tune stations in single-
step increments. (See page 26 for
more information.)

w

These

controls do not control any functions
of the AVR35RDS, but they are used
extensively when operating a wide
variety of CD players, cassette decks
and VCRs. (See page 28 for
information on programming the
remote to utilize these buttons.)

x

Press this

button to begin the process for
setting the delay times used by the
AVR35RDS when processing
surround sound. After pressing this
button the delay times are entered
by pressing the 

button 

j, and

then using the 

⁄

¤

buttons

h to

change the setting. Press the Set
button again to complete the
process. (See page 20 for more
information.)

y

›

This button is

used to select the type of digital input
used with any one of the input sources
connected to the AVR35RDS. After
pressing this button, use the 

⁄

¤

buttons

h to make your selection

between OPTICAL

E or COAXIAL G

digital. Press the 

button 

j to

enter your choice. (See page 24 for
more information.)

z

Press

this button to begin the process of
configuring the AVR35RDS’s Bass
Management System for use with the
type of speakers used in your
system. Once the button has been
pressed, use the 

⁄

¤

buttons

h to

select the channel you wish to set up.
Press the 

button 

j, and then

select another channel to configure.
When all adjustments have been
completed, press the Set button
twice to exit the settings and return to
normal operation. (See page 17 for
more information.)

`

Press this button to

momentarily silence the AVR35RDS or
TV set being controlled, depending on
which device has been selected.

Press these buttons to

raise or lower the system volume.

Press this button to begin

the sequence used to calibrate the
AVR35RDS’s output levels. (See page
19 for more information on calibrating
the AVR35RDS.)

This button does not

function with the AVR35RDS, but it is
available for use with other devices.