AVR 35 (serv.man4) - Harman Kardon Audio User Guide / Operation Manual. Page 14

Remote Control Functions

12

IMPORTANT NOTE:

The

AVR35RDS’s remote may be
programmed to control up to five
additional devices, including the
AVR35RDS. Before using the remote,
it is important to remember to press
the 

button

b c that corresponds to the unit
you wish to operate. In addition, the
AVR35RDS’s remote is shipped from
the factory to operate the AVR35RDS
and Harman Kardon CD players and
cassette decks. The remote is also
capable of operating a wide variety
of other products using the control
codes that are part of the remote.
Before using the remote with other
products, follow the instructions on
pages 28–29 to program the proper
codes for the products in your
system.

It is also important to remember that
many of the buttons on the remote
take on different functions,
depending on the product selected
using the Device Control Selectors.
The descriptions shown here
primarily detail the functions of the
remote when it is used to operate the
AVR35RDS. (See pages 28–31 for
information about alternate functions
for the remote’s buttons.)

a

This LED is used as an indicator to
assist in programming the remote
control. (See pages 28–31 for more
information on programming the
AVR35RDS.)

b

Press this button

to use the remote control for operation
of the AVR35RDS. Note that the button
will briefly turn red after it has been
pressed to confirm your selection.

c

Press

one of these buttons to use the
remote to control the functions of
another audio/video device. Note that
the button will briefly turn red after it
has been pressed to confirm your

selection. (See pages 28–31 for
information on programming the
AVR35RDS’s remote to operate these
devices.)

d

Press this button

to turn the currently selected device
on or off.

e

Press this button

to place the unit in the Sleep mode.
After the time shown in the display,
the AVR35RDS will automatically go
into the Standby mode. Each press
of the button changes the time until
turn-off in the following order:

f

⁄

¤

When the remote is being used to
control a TV, VCR or Cable box, press
these buttons to change the channel
being viewed.

g

Press

this button to begin the process of
changing the surround mode. After
the button has been pressed, use the

⁄

¤

buttons

h to select the desired

surround mode. (See page 24 for
more information.) 

h

⁄

¤

These are multi-

purpose buttons. They will be used
most frequently to select a surround
mode. To change the surround mode,
first press the 

button 

g. Next

press these buttons to scroll up or
down through the list of surround
modes that appear in the 

33. (See page 24 for more

information.) These buttons are also
used to increase or decrease the
AVR35RDS’s output levels when
configuring the unit with either the
internal test tone or an external
source. (See pages 19 and 28 for
more information.) They are also used
to enter delay time settings after the

button 

x has been pressed.

(See page 20 for more information.)

90

min

80

min

70

min

60

min

50

min

40

min

30

min

20

min

10

min

5

min

1

min

OFF

i

‹

This button

is used to start the process of setting
the AVR35RDS’s output levels to an
external source. Once this button is
pressed, use the 

⁄

¤

buttons 

h to

select the channel being adjusted,
then press the 

button 

j,

followed by the 

⁄

¤

buttons again to

change the level letting. (See page
27 for more information.)

j

This button is used

to enter settings into the AVR35RDS’s
memory. It is also used in the setup
procedures for delay time, speaker
configuration and channel output
level adjustment. (See pages 17–21
for complete information.)

k

Press this button to

activate the “Night” mode, preventing
loud playback when the digital
modes are in use without altering the
dynamic range of the output signal.

l

Press these

buttons to select an input source for
the AVR35RDS. The AM/FM button is
also used to switch between
frequency bands when the tuner is in
use.

NOTE:

Pressing one of these buttons

selects the source only. In order to
control the actual source machine
using the remote you must press the

button 

c

for the desired product.

m

This button does not

have a function for the AVR35RDS,
but when the remote is used to
control certain CD players, TV sets
and VCRs it may be used to select
tracks or channel numbers

n

These buttons

serve as a ten-button numeric
keypad to enter tuner preset
positions. They are also to be used to
select channel numbers when 

has been selected on the remote, or
to select track numbers on a CD,
DVD or LD player, depending on how
the remote has been programmed.