Read JBL PULSE (serv.man6) EMC - CB Certificate online
- Page 4 of 8 -
www.nemko.com
Report No. 241619
Clause
Requirement - Test
Result - Remark
Verdict
2.6.5.4
Replace 1st sentence with the following.
Protective earthing connections of CLASS I
EQUIPMENT shall make earlier and break later
than the supply connections in each of the
following:
Protective earthing connections of CLASS I
EQUIPMENT shall make earlier and break later
than the supply connections in each of the
following:
Class III equipment.
N/A
2.6.5.8A
Add the following new clause. after 2.6.5.8A
2.6.5.8A Earthing of CLASS 0I EQUIPMENT Plugs
with a lead wire for earthing shall not be used for
equipment having a rated voltage exceeding 150V.
For plugs with a lead wire for earthing, the lead
wire shall not be earthed by a clip.
CLASS 0I EQUIPMENT shall be provided with an
earthing terminal or lead wire for earthing in the
external location where easily visible.
2.6.5.8A Earthing of CLASS 0I EQUIPMENT Plugs
with a lead wire for earthing shall not be used for
equipment having a rated voltage exceeding 150V.
For plugs with a lead wire for earthing, the lead
wire shall not be earthed by a clip.
CLASS 0I EQUIPMENT shall be provided with an
earthing terminal or lead wire for earthing in the
external location where easily visible.
Class III equipment.
N/A
3.2.3
Add the following after Table 3A:
Table 3A applies when cables complying JIS C
3662 or JIS C 3663 are used. In case of other
cables, cable entries shall be so designed that a
conduit suitable for the cable used can be fitted.
Table 3A applies when cables complying JIS C
3662 or JIS C 3663 are used. In case of other
cables, cable entries shall be so designed that a
conduit suitable for the cable used can be fitted.
Class III equipment.
N/A
3.2.5.1
Add the following to the last of first dashed
paragraph. Or mains cords shall be of the sheathed
type complying with Appendix 1 of Article 1 of the
Ministerial Ordinance on stipulating technical
requirements for the Electrical Appliance.
Add the following to the last of second dashed
paragraph. Or mains cords shall be of the sheathed
type complying with Appendix 1 of Article 1 of the
Ministerial Ordinance on stipulating technical
requirements for the Electrical Appliance.
Delete 1) in Table 3B
paragraph. Or mains cords shall be of the sheathed
type complying with Appendix 1 of Article 1 of the
Ministerial Ordinance on stipulating technical
requirements for the Electrical Appliance.
Add the following to the last of second dashed
paragraph. Or mains cords shall be of the sheathed
type complying with Appendix 1 of Article 1 of the
Ministerial Ordinance on stipulating technical
requirements for the Electrical Appliance.
Delete 1) in Table 3B
Class III equipment.
N/A
3.3.4
Add the following note to Table 3D:
Note For cables other than those complying with
JIS C 3662 or JIS C 3663, terminals shall be
suitable for the size of the intended cables.
Note For cables other than those complying with
JIS C 3662 or JIS C 3663, terminals shall be
suitable for the size of the intended cables.
Class III equipment.
N/A
3.3.7
Add the following after the first sentence:
This requirement is not applicable to the external
earthing terminal of Class 0I equipment.
This requirement is not applicable to the external
earthing terminal of Class 0I equipment.
Class III equipment.
N/A
4.3.4
Add the following after the first sentence:
This requirement also applies to those connections
in Class 0I equipment, where CLEARANCE or
CREEPAGE DISTANCES over BASIC
INSULATION would be reduced to less than the
values specified in 2.10.
This requirement also applies to those connections
in Class 0I equipment, where CLEARANCE or
CREEPAGE DISTANCES over BASIC
INSULATION would be reduced to less than the
values specified in 2.10.
Class III equipment.
N/A
Click on the first or last page to see other PULSE (serv.man6) service manuals if exist.