Read Sony KV-SZ292M31 (serv.man2) Service Manual online
– 10 –
KV-SZ292M31/M50
RM-GA002
2-7. Insertion of Lead Assy, H Static
2-8. Dressing of Conn Assy, 5P Front In
Insert Lead Assy, H Static into CRT socket and RV750
as shown.Make sure the wire is naturally curved, to avoid
touching CRT neck.
as shown.Make sure the wire is naturally curved, to avoid
touching CRT neck.
2-9. Dress Lead Assy, Earth and Conn Assy,
5P In with purse lock
Ø
5
Make a 'S' shaped loop on Conn Assy, 5P Front In
as shown. Keep wires away from heatsink A010.
as shown. Keep wires away from heatsink A010.
Next, Conn Assy, 5P Front In is dressed together with
Lead Assy,Earth using purse lock Ø 5. Refer to 2-9.
Lead Assy,Earth using purse lock Ø 5. Refer to 2-9.
2-10. CV Board Connector Assy wire dressing
Note: Dress while chassis is halfway docked into beznet.
CAUTION:
Prevent tie, cable from touching rear cover or any
enclosures by turning them away from it --> avoid
rattle sound. Also prevent tie, cable's end from
touching solder side of board.
Prevent tie, cable from touching rear cover or any
enclosures by turning them away from it --> avoid
rattle sound. Also prevent tie, cable's end from
touching solder side of board.
CAUTION:
Prevent tie, cable from touching rear cover or any
enclosures by turning them away from it --> avoid
rattle sound. Also prevent tie, cable's end from
touching solder side of board.
Prevent tie, cable from touching rear cover or any
enclosures by turning them away from it --> avoid
rattle sound. Also prevent tie, cable's end from
touching solder side of board.
i) Dress Conn Assy, 6P and Conn Assy, 4P VM using tie,
cable at alignment hole 'B' on CV board as shown.
ii) Dress Conn Assy, 4P 200V; Conn Assy, 6P; Conn Assy,
4P VM; Lead Assy, G2 and Lead Assy, Focus with purse
lock Ø 5.
cable at alignment hole 'B' on CV board as shown.
ii) Dress Conn Assy, 4P 200V; Conn Assy, 6P; Conn Assy,
4P VM; Lead Assy, G2 and Lead Assy, Focus with purse
lock Ø 5.
Lead Assy, H static
CRT socket
CRT neck
Lead Assy, Earth
Lead Assy, Speaker
Heatsink A010
Conn Assy, 5P
Front In
RV750
Lead Assy, Earth
Conn Assy, 5P Front In
Heatsink A010
Tie, cable at alignment hole 'B'
Conn Assy, 6P
Conn Assy, 4P VM
Conn Assy
,
4P
VM
Conn Assy
,
4P
200V
Conn Assy
,
6P
Conn Assy
,
Focus
Conn Assy
,
G2
Conn Assy, 4P 200V
Lead Assy, G2
Lead Assy, Focus
Pin, wire A707
Purse lock Ø 5
Purse lock Ø 5
Purse lock Ø 5
Lead Assy, Speaker is not dressed
together with purse lock. Keep Lead Assy,
Speaker away from heatsink A010 by
dressing it close to the CRT
Make a 'S' shaped loop on
Conn Assy, 5P Front In
and dress together with
Lead Assy, Earth using
purse lock Ø 5
Conn Assy, 5P
Lead Assy, Earth
Click on the first or last page to see other KV-SZ292M31 (serv.man2) service manuals if exist.