Read Sony KD-32NX200U Service Manual online
- 13 -
Memory Stick operation
31
MEMORY
STICK
DIGIT
AL
OK
VTR
TV
DVD
MEMORYSTICK
DIGIT
AL
VTR
TV
DVD
OK
Memory Stick Index
Page +
Page 1/3
Index
This feature enables you to view on screen the JPEG DCF format pictures from your
memory stick.
memory stick.
Slideshow
This feature allows you to display all the memory stick pictures as a slideshow
presentation on the TV screen.
presentation on the TV screen.
1.
Press the MEMORY STICK button on the remote control to display the
‘Memory Stick’ menu on the TV screen.
‘Memory Stick’ menu on the TV screen.
2.
Press the
V
or
v
button to highlight ‘Index’ then press the OK button to
display the ‘Memory Stick Index’ screen.
3.
Press the
v
,
V
,
B
or
b
buttons to highlight the required picture, then press the
OK button to display the picture fully on the TV screen.
Note: Only a limited number of pictures can be displayed on the Index screen at one
time. If your required picture is not visible, highlight
‘Page +’ then press the
OK button to view the next set of pictures. Press the
v
,
V
,
B
or
b
buttons to
select your desired picture then press the OK button to view.
4.
Use the
v
,
V
,
B
or
b
buttons to highlight ‘Back’. Press the OK button to return
to the ‘Memory Stick’ menu or press the DIGITAL/
button at any time to
return to normal TV operation.
1.
Press the MEMORY STICK button on your remote control to display the
‘Memory Stick’ menu on the TV screen.
‘Memory Stick’ menu on the TV screen.
2.
Press the
V
or
v
button to highlight Slideshow.
3.
Press the OK button to start the slideshow. (To change the length of time an
image is displayed refer to the ‘Setup’ section on the following page.)
image is displayed refer to the ‘Setup’ section on the following page.)
4.
Press the OK button during the slideshow to return to the ‘Memory Stick’
menu. Press the DIGITAL/
menu. Press the DIGITAL/
button to return to normal TV operation.
Connecting other equipment
37
MODE
1
4
7
3
6
9
2
5
8
8
0
VTR
TV
DVD
Remote control operation for VCR and DVD players
This remote control has been configured to operate not only Sony DVDs and VCRs but also those made by other manufacturers. To
operate other makes of DVD and VCR using this remote control, complete the following procedure:
operate other makes of DVD and VCR using this remote control, complete the following procedure:
1.
Find the 3 digit code for your brand from the list below. If your brand has more than one code
allocated to it, make a note of the first code only at this stage.
allocated to it, make a note of the first code only at this stage.
2.
Press the MODE button on the remote control until either the VCR green light or the DVD green
light is illuminated.
light is illuminated.
3.
With the required green light illuminated, press and hold down the YELLOW button for
approximately 6 seconds, until the light starts to flash.
approximately 6 seconds, until the light starts to flash.
4.
Using the numbered buttons, enter the 3 digit code for your DVD or VCR. Once a correct
number has been entered, all three green lights will illuminate momentarily.
number has been entered, all three green lights will illuminate momentarily.
5.
Turn on your DVD or VCR and check that the remote control operates the main functions. If not,
repeat steps 2 - 4 and enter the next 3 digit code allocated to your brand of VCR or DVD.
repeat steps 2 - 4 and enter the next 3 digit code allocated to your brand of VCR or DVD.
6.
When you wish to use the remote control to operate the TV again, press the MODE button until
the TV green light illuminates. Don’t forget to select VCR or DVD using the MODE button every
time you wish to operate that equipment with this remote control.
the TV green light illuminates. Don’t forget to select VCR or DVD using the MODE button every
time you wish to operate that equipment with this remote control.
Note: The brand codes you set may be lost if weak batteries are not replaced immediately. Should this
happen, use the above procedure to reset the code. A small label has been attached to the inside of the
battery cover for you to make a note of your brand codes.
Not all brands and models of DVDs or VCRs are covered in this list. However, Sony will endeavour to
update the software periodically, so please refer to the code table provided with your remote control.
happen, use the above procedure to reset the code. A small label has been attached to the inside of the
battery cover for you to make a note of your brand codes.
Not all brands and models of DVDs or VCRs are covered in this list. However, Sony will endeavour to
update the software periodically, so please refer to the code table provided with your remote control.
VCR Brand List
DVD Brand List
Brand Code
Brand
Code
SONY (VHS)
301, 302, 303, 309
SONY
001
SONY (BETA)
301, 302, 303, 309
AIWA
021
SONY (DVD)
304, 305, 306
DENON
018, 027, 020, 002
AIWA
325, 331, 351
GRUNDIG
009, 028, 023, 024, 016. 003
AKAI
326, 329, 330
HITACHI
025, 026, 015, 004
DAEWOO
342, 343
JVC
006, 017
GRUNDIG
358, 355, 360, 361, 320, 351
KENWOOD
008
HITACHI
327, 333, 334
LG
015, 014
JVC
314, 315, 322, 344, 352, 353,
LOEWE
009, 028, 023, 024, 016. 003
LG
332, 338
MATSUI
013, 016
LOEWE
358, 355, 360, 361, 320, 351
ONKYO
022
MATSUI
356, 357
PANASONIC
018, 027, 020, 002
ORION
328
PHILIPS
009, 028, 023, 024, 016. 003
PANASONIC
321, 323
PIONEER
004
PHILIPS
311, 312, 313, 316, 317, 318,
SAMSUNG
011, 014
SAMSUNG
339, 340, 341, 345
SANYO
007
SANYO
335, 336
SHARP
019, 027
SHARP
324
THOMSON
012
THOMSON
319, 350
TOSHIBA
003
TOSHIBA
337
YAMAHA
018, 027, 020, 002
Click on the first or last page to see other KD-32NX200U service manuals if exist.