Read Sony KD-32NX200U Service Manual online
- 14 -
Additional Information
38
Specifications
TV System
I/DVB-T
Colour System
PAL
NTSC 3.58, 4.43 (only Video In)
MPEG-2 MP@ML
NTSC 3.58, 4.43 (only Video In)
MPEG-2 MP@ML
Channel Coverage
UHF:
B21 - B69
Picture Tube
KV-32NX200
FD Trinitron Approx. 82cm
KV-36NX200
FD Trinitron Approx. 91cm
Sound Output
Left/Right:
2x20W (music power), 2x10W (RMS)
Subwoofer
1x30W (music power), 1x15W (RMS)
Power Consumption
KV-32NX200
154W (1w standby)
KV-36NX200
182W (1w standby)
Dimensions (w x h x d)
KV-32NX200
Approx. 910 x 445.5 x 590mm
KV-36NX200
Approx. 1010 x 645 x 607mm
Weight
KV-32NX200
Approx. 67kg
KV-36NX200
Approx. 87kg
Rear Terminals
21-pin Euro connector (CENELEC standard) including audio/video
input, RGB input, TV audio/video output.
21-pin Euro connector (CENELEC standard) including audio/video
input, RGB input, TV audio/video output
input, RGB input, TV audio/video output
21-pin Euro connector (CENELEC standard) including audio/video
input, S-video input, selectable audio/video output.
input, S-video input, selectable audio/video output.
Conditional Access Module
RF In
Audio output - RCA phono jacks
Front Terminals
Video input - phono jack
S video input - 4 pin DIN
Audio inputs - phono jacks
Headphones jack - minijack stereo
Accessories Supplied
RM-939 remote control (1)
IEC designated size AA (R6) battery (2)
RF Loopthrough cable
IEC designated size AA (R6) battery (2)
RF Loopthrough cable
1
2
3/
s
3
4
s
4
4
Design and specification are subject to change without notice
Additional Information
39
Troubleshooting
Here are some simple solutions to problems which may affect the picture and sound.
•
If you continue to have these problems, have your TV serviced by qualified personnel or you can contact the Sony UK
Digital HelpLine on 0870 600 1717.
Digital HelpLine on 0870 600 1717.
•
NEVER open the casing yourself.
Problem
Possible causes
Solutions
No picture, no sound.
•
Power off
•
TV in standby.
•
Aerial disconnected.
•
Plug in the TV
•
Press the
button on the front of the TV. If the
indicator is on press the
button on the remote control.
•
Check aerial connection
Poor or no picture (screen is
dark), but good sound.
dark), but good sound.
•
Picture preset level adjustment
•
Select ‘Picture Adjustment’ menu then adjust adjust the
brightness, picture and colour levels.
brightness, picture and colour levels.
No picture on any channel after
digital tuning.
digital tuning.
•
No digtal transmission in your area.
•
No digital transmissions from the
transmitter you are currently using.
transmitter you are currently using.
•
Unsuitable aerial.
•
Weak signal.
•
Tune in all the Analogue channels available using the
‘Manually tuning analogue signals’ instructions of this
manual to tune in available analogue channels, then contact
local installer to find out when digital transmissions begin in
your area.
‘Manually tuning analogue signals’ instructions of this
manual to tune in available analogue channels, then contact
local installer to find out when digital transmissions begin in
your area.
•
Contact a local installer to find out which transmitter you
should be pointing your aerial at.
should be pointing your aerial at.
•
Change your aerial to cover the channels used by digital
programmes.
programmes.
•
Ensure aerial is correctly aligned to transmitter.
•
Ensure aerial is is plugged directly into the TV (not through
other equipment).
other equipment).
•
Upgrade to a higher gain aerial.
Some channels are blank.
•
Scrambled or subscription-only
channel.
channel.
•
Programme used only for data (no
picture or sound).
picture or sound).
•
Programme not being transmitted.
•
Subscribe to pay-per-view broadcaster.
•
See ‘Skipping a programme’ section.
•
See ‘Re-arranging your channels’ section.
Standby indicator flashing.
•
Fault (irregular flash)
•
Digital mode Timer Record active
(regular flash).
(regular flash).
•
Do not open the cabinet, refer to qualified personnel.
•
Contact nearest SONY Service Centre.
•
Will clear when Timer Recording stops.
Good picture, no sound
•
Volume control.
•
Press the
+ button on the remote control.
•
If
is displayed on the screen, press the
button on
the remote control.
Poor picture quality
•
Wrong external mode selected for an
RGB video source.
RGB video source.
•
Press the
button repeatedly until the RGB symbol
is displayed on screen.
No colour on colour
programmes
programmes
•
Colour level setting.
•
Select ‘Picture Adjustment’ menu then adjust the colour
setting.
setting.
Remote control does not
function
function
•
Batteries low.
•
Replace batteries.
Distorted picture when
changing programmes or
selecting teletext
changing programmes or
selecting teletext
•
Inputs from external equipment not
switched off.
switched off.
•
Switch off all additionally connected equipment.
/
Click on the first or last page to see other KD-32NX200U service manuals if exist.