MPK-DVF6 - Sony Movie Service Manual (repair manual). Page 2

MPK-DVF6

This section is extracted from
instruction manual (3-090-357-11).

Check that the following accessories are supplied with your marine pack.

1

Camera mounting shoe B (1)

2

Spacer C (1)

3

Camera mounting shoe D (1)

4

Cushions for camera mounting shoe
D (2)

5

Camera mounting shoe E (1)

6

Camera mounting shoe F (1)

7

Camera mounting shoe G (1)

8

Screw plate for camera mounting
shoe B, D and E (2)

9

Screw driver part (1)
Attachment for the camera mounting
shoe B

0

A/V conversion cable (1)

qa

Lithium battery CR2 (1)

qs

O-ring (1)

qd

Underwater wide-conversion lens
(VCL-MK2) (1)

qf

Sunshade (1)

qg

Reflex prevention ring (3)
Large:

ø 37 mm (1)

Medium: ø 30 mm (1)
Small:

ø 25 mm (1)

qh

Colour filter (VF-MK2) (1)

qj

Grease (1)

qk

Strap (3)

ql

Carrying bag (1) Carrying belt (1)

1

2

3

4

5

6

7

8

9

0

qa

qh

qj

qk

ql

B

qs

qd

qf

qg

Thick

Thin

Before installing your camcorder in the marine pack, prepare the camcorder according
to this chapter.
The procedure may be different depending on your camcorder type.
For details, please refer to the operating instructions supplied with your camcorder.
You can also install camcorder models different to the one shown in the illustration.

Remove the lens cap, shoulder strap, conversion lens, filter or lenshood from
the camcorder.

Attach a fully charged battery pack.
Some models can be fitted to a mounting shoe.

Insert a cassette tape or “Memory Stick”.

Select the media you want to record onto.

Attach the reflex prevention ring to the lens.

for DCR-TRV50/TRV50E/TRV40/TRV40E/TRV30/TRV30E/TRV20/TRV20E/
TRV9/TRV9E

: ø 37 mm (large)

for DCR-TRV118E/TRV116E/TRV27/TRV27E/TRV25/TRV25E/TRV24E/TRV18/
TRV18E/TRV17/TRV17E/TRV16/TRV16E/TRV15/TRV15E/TRV11/TRV11E/
TRV10/TRV10E/TRV8/TRV8E/TRV6/TRV6E

: ø 30 mm (medium)

for DCR-TRV900/TRV900E/TRV890E

: not necessary

for DCR-HC40/HC40E/HC30/HC30E/HC20/HC20E/HC18E/HC16E/PC109/
PC109E/PC108/PC108E/PC107E/PC106E

: ø 25 mm (small)

Be sure not too tighten prevention ring.

Attach the camera mounting shoe.

Use mounting shoe F and the A/V
conversion cable.
1 Attach mounting shoe F firmly to the

camcorder.

2 Connect the A/V conversion cable to the

camcorder’s AUDIO/VIDEO jack.

Use mounting shoe G only.
1 Attach mounting shoe G firmly to the

camcorder.

2 Connect the A/V connecting cable of the

shoe to the camcorder’s AUDIO/VIDEO
jack.

3 Attach the battery adaptor that comes

with mounting shoe G to battery
terminal of the camcorder.
If there is a battery installed in the
camcorder, remove it.

4 Attach the battery to the rear of

mounting shoe G 

A.

Fasten the battery firmly with the belt,
as shown in the illustration.

A

G

F

Camera mounting
 shoe B

Screw plate

Use camera mounting shoe B,
spacer C, and the screw plate.
1 Attach the spacer C to shoe B.
2 Attach the screw plate to

position 3 on shoe B so that the
catch on the reverse side of the
shoe clicks into place.

3 Fasten the screw of the screw

plate to the tripod screw hole of
the camcorder and tighten
firmly.

4 Connect the A/V connecting

cable of the shoe to the
camcorder’s AUDIO/VIDEO
jack.

Spacer C

Use camera mounting shoe B and the screw
plate.
Check the installing position of the screw plate
for your camcorder against the table below.

DCR-

Camera mounting Shoe B

TRV900/TRV900E

2

TRV890E

2

TRV9/TRV9E

1

1 Attach the screw plate to

position 1 on shoe B so that the
catch on the reverse side of the
shoe clicks into place.

2 Fasten the screw of the screw

plate to the tripod screw hole of
the camcorder and tighten
firmly.

3 Connect the A/V connecting

cable of the shoe to the
camcorder’s AUDIO/VIDEO
jack.

Camera
mounting
shoe B

1

3

Screw plate