Read Sony MHS-TS22 (serv.man2) Service Manual online
MHS-TS22_ADJ
5-7
5-2-5. Set Language Destination
Language Destination Setting:
Save “lang.txt” in the root directory of the slot named ”BLOGGIE”.
The content of “lang.txt” is as follows:
Save “lang.txt” in the root directory of the slot named ”BLOGGIE”.
The content of “lang.txt” is as follows:
Language Destination (for example: 6_U) (enter key)
Product ID (10bit) (enter key) (refer to “5-3 PRODUCT ID LIST”)
S/N (8bit) (enter key)
Product ID (10bit) (enter key) (refer to “5-3 PRODUCT ID LIST”)
S/N (8bit) (enter key)
The following is an example of 6_U Language Destination Setting for MHS-TS22 Black camera.
6_U
0080700130
08432345
0080700130
08432345
Especially Attention:
1) The enter key must be the end symbol of each row.
2) For the Product ID, refer to “5-3 PRODUCT ID LIST”, and the Product ID must be 10bit.
1) The enter key must be the end symbol of each row.
2) For the Product ID, refer to “5-3 PRODUCT ID LIST”, and the Product ID must be 10bit.
If the Product ID is less than 10 bit, add 0 before the Product ID.
3) The S/N must be 8 bit. It refer to the serial number of shipment.
Adjustment order
The adjustment is finished abnormally.
Set LangDest NG
Pls check Lang.txt
or if MassProduct
Pls check Lang.txt
or if MassProduct
Fig. 5-2-28
Malfunction of Set Language
Destination
Destination
In case of the Set Language
Destination is failed, reset the
language destination.
Destination is failed, reset the
language destination.
Screen display
The adjustment finished normally.
Set LangDest OK
Dest: 6_U
ProductNum:
0080700130
S/N:
08432345
Color: Black
Pls l/R Key to check result
Dest: 6_U
ProductNum:
0080700130
S/N:
08432345
Color: Black
Pls l/R Key to check result
Fig. 5-2-27
The adjustment is complete.
Note: The screen shown above is an example.
Confirm the indication
on the screen.
Finished normally.
Finished abnormally.
Press the set key, then Language Destination Setting starts.
Put the lang.txt file into the BLOGGIE folder (when writing a destination to the service board).
Set the camera to the adjustment mode.
* For the setting procedure of the adjustment mode, refer to “5-1-4. Setting the Adjustment Mode” (Page 5-3).
In case of the adjustment is finished normally,
the adjustment completion indication appears
on the screen. (Fig. 5-2-27)
The adjustment will proceed to "Check all above
adjustment result", do not execute any key operation.
the adjustment completion indication appears
on the screen. (Fig. 5-2-27)
The adjustment will proceed to "Check all above
adjustment result", do not execute any key operation.
In case of the adjustment is finished abnormally,
the following indication appears on the screen.
(Fig. 5-2-28)
In this case, confirm the adjusting environment
and readjust.
the following indication appears on the screen.
(Fig. 5-2-28)
In this case, confirm the adjusting environment
and readjust.
5-2-6. Check all above Adjustment Result
After doing set language adjustment, it can be checked all above adjustment result.
Even for mass-production boards for which destination setting has been made, the existing destination information is shown by executing
“Check all above adjustment result” without putting the “lang.txt” file into the BLOGGIE drive.
Even for mass-production boards for which destination setting has been made, the existing destination information is shown by executing
“Check all above adjustment result” without putting the “lang.txt” file into the BLOGGIE drive.
There is less than one adjustment is NG.
(Take one for example (Fig.5-2-30 to Fig.5-2-3
(Take one for example (Fig.5-2-30 to Fig.5-2-3
4).)
X AF Adjust: NG
O AWB Adjust: OK
O BrightDefectPix: OK
O DarkDefectPix: OK
O LensShading: OK
O BrightDefectPix: OK
O DarkDefectPix: OK
O LensShading: OK
O AF Adjust: OK
X AWB Adjust: NG
O BrightDefectPix: OK
O DarkDefectPix: OK
O LensShading: OK
O DarkDefectPix: OK
O LensShading: OK
Fig. 5-2-30
Fig. 5-2-31
O AF Adjust: OK
O AWB Adjust: OK
O AWB Adjust: OK
X BrightDefectPix: NG
O DarkDefectPix: OK
O LensShading: OK
O LensShading: OK
O AF Adjust: OK
O AWB Adjust: OK
O BrightDefectPix: OK
O AWB Adjust: OK
O BrightDefectPix: OK
X DarkDefectPix: NG
O LensShading: OK
Fig. 5-2-32
Fig. 5-2-33
O AF Adjust: OK
O AWB Adjust: OK
O BrightDefectPix: OK
O DarkDefectPix: OK
O AWB Adjust: OK
O BrightDefectPix: OK
O DarkDefectPix: OK
X LensShading: NG
Fig. 5-2-34
Screen display
All above adjustment is OK.
O AF Adjust: OK
O AWB Adjust: OK
O BrightDefectPix: OK
O DarkDefectPix: OK
O LensShading: OK
O AWB Adjust: OK
O BrightDefectPix: OK
O DarkDefectPix: OK
O LensShading: OK
Fig. 5-2-29
Confirm the indication
on the screen.
Finished normally.
Finished abnormally.
Touch the right key or left key, then All above adjustment Checking starts.
Check that Set Language Destination (Page 5-7) is finished normally.
In case of the adjustment is finished normally,
the adjustment completion indication appears
on the screen in a moment. (Fig. 5-2-29)
Then the adjustment will proceed to "Remove
adjustment FW" automatically.
the adjustment completion indication appears
on the screen in a moment. (Fig. 5-2-29)
Then the adjustment will proceed to "Remove
adjustment FW" automatically.
In case of the adjustment is finished abnormally,
the following indication appears on the screen.
(Take one for example (Fig.5-2-30 to Fig.5-2-
the following indication appears on the screen.
(Take one for example (Fig.5-2-30 to Fig.5-2-
34).)
In this case, readjust the NG items.
Adjustment order
Click on the first or last page to see other MHS-TS22 (serv.man2) service manuals if exist.