MHS-TS22 (serv.man2) - Sony Movie Service Manual (repair manual)

mhs-ts22 (serv.man2) service manual
Model
MHS-TS22 (serv.man2)
Pages
8
Size
162.51 KB
Type
PDF
Document
Service Manual
Brand
Device
Movie / ADJUSTMENT MANUAL
File
mhs-ts22-sm2.pdf
Date

Read Sony MHS-TS22 (serv.man2) Service Manual online

Sony Corporation
Revision History
SECTION 5
ADJUSTMENT
ADJ
MHS-TS22_ADJ
983465851.pdf
2012C08-1
© 2012.03
Published by Sony Techno Create Corporation
Ver. 1.0  2012.03
9-834-658-51
MHS-TS22
Link
• PREPARATIONS
•  Adjustment Items When Replacing Lens 
Block (includes CMOS) and Main Board 
Assy
•  List of Service Tools and Equipment
•  Keys and Functions
•  Connecting the Equipment
•  Setting the Adjustment Mode
• CAMERA SECTION ADJUSTMENTS
• Auto Focus Adjustment
•  AWB Bad Pixel Adjustment
• Lens Shading Adjustment
• Bright Pixel Adjustment
•  Set Language Destination
•  Check all above Adjustment Result
• Remove Adjustment FW
•  PRODUCT ID LIST
Ver.
Date
History
Contents
S.M. Rev.
issued
1.0
2012.03
Official Release
5-2
MHS-TS22_ADJ
5. ADJUSTMENT
5-1. PREPARATIONS
5-1-2. List of Service Tools and Equipment
5-1-3. Keys and Functions
Following are keys and functions used in adjustment. (Fig. 5-1-2)
Movie button
LCD screen/Touch panel
ON/OFF (Power) button
(Shutter) button
Left Key
Set Key
Up Key
Down Key
Menu Key
Right Key
 Fig. 
5-1-2
5-1-4. Connecting the Equipment
Connect the USB to USB charging adaptor and perform the adjustment during charging the built-in battery. (Fig.5-1-3)
Charge lamp may turn off during adjustment, but it does not affect the charging.
(J-6082-384-A)
To USB jack
Be sure to connect the USB charging adaptor
in "5-2-4. Bright Pixel Adjustment."
USB extension cable
(A plug to A socket)
(Commercially available)
Ball head
(Commercially available)
To USB connector
USB charging adaptor
(AC-U50A series or AC-U501AD)
 Fig. 
5-1-3
 Fig. 
5-1-1
Note1:
For the chart, search “J-6082-563-A” in the JIG & Software on TISS homepage, download the PDF file and print out it on the A4 size whitepaper.
Note2:
Print out the Near Focus chart from the Adjustment Manual of MHS-FS3/FS3K (9-834-570-5[])  in A4 size.
This chart is indicated to be the one for MHS-FS3/FS3K in the manual, but is also available for MHS-TS22.
5-1-1. Adjustment Items When Replacing Lens Block (includes CMOS) and Main Board Assy
When replacing these parts, adjust the items indicated by “ z ” in the following table.
Adjustment item
Replaced parts
Lens Module
(includes CMOS)
Main Board Assy
Auto Focus Adjustment
z
z
AWB Bad Pixel Adjustment
z
z
Lens Shading Adjustment
z
z
Bright Pixel Adjustment
z
z
Set Lang Check Result
z
J-1
J-3
J-5
J-4
J-2
J-7
J-8
Small pattern box
PTB-1450
J-6082-557-A
Mini flange back jig
J-6082-719-A
or
Flange back
adjustment jig
J-6082-563-A
Camera table
J-6082-384-A
USB charging adaptor
AC-UD series,
AC-U501AD series
or
AC-U50A series
USB extension cable
(A plug to A socket)
(Commercially available)
Ball head
(Tiltable angle: 90° max.)
(Commercially available)
J-9
Chart
(Note1)
or
Near Focus chart
(for MHS-FS3)
(Note2)
Light balance filter
LB140
J-6080-058-B
or
Filter for color
temperature correction
(C14)
J-6080-058-A
Clear chart
J-6082-560-A
J-10
MHS-TS22_ADJ
5-3
5-1-5. Setting the Adjustment Mode
1)  Download the firmware file “TS22_[][][]ADJ.zip” from the TISS homepage.
 
Uncompress the “TS22_[][][]ADJ.zip”, then confirm that it includes the following item.
• SDW5090.bin
2)  Save the uncompressed file “SDW5090.bin” in the root directory of the slot named “START”.
 Note:
  Saving it in other directories causes a malfunction of program.
3)  With the camera turned off.
4)  Disconnect the USB cable from PC.
5)  Keep pressing the Power button while pressing the Set key.
6)  Release the Set key about one second later, and then release the Power button.
7)  Start the unit in the adjustment mode several seconds later and check that the screen shown in Fig. 5-1-4 appears.
8)  Connect the equipment to be used by referring to “5-1-4 Connecting the Equipment”.
 
Key Down: AWBBadPixel Adjust
Key Left: BrightPixel Adjust
Key Right: LensShading Adjust
Key Set: Check Result
Key Up: AutoFocus Adjust
MHS-TS22 V3.01ADJ MCUParts ADJ
 
Fig. 5-1-4
On the screen that appears upon completion of each adjustment, touch the Menu key to return to the initial screen (Fig. 5-1-4).
However, only after the bright pixel adjustment has been completed, turn off the power of the unit.
Turning off the power after the bright pixel adjustment deletes temporary files generated during the AWB bad pixel adjustment from the BLOGGIE drive.
MHS-TS22_ADJ
5-4
(2) Near Focus Adjustment
Note:  Perform the Near Focus Adjustment after the Far Focus Adjustment.
1)  Be sure to set 12 ±1cm distance between the chart and the tip of camera lens.
2)  Check that the center of chart meets the center of shot image screen.
Color temperature = 5000 ± 300K
Luminance: LV9 to 11
Be sure not to turn off the power during adjusting.
The adjustment finished normally.
Left Near OK OOO
Left Mech OK OOO
Fig. 5-2-5
The adjustment is complete.
The adjustment is finished abnormally.
Left Near OK OOO
Left Mech NG XXX
ADJ NG Pre S1 ReAdj
Fig. 5-2-6
Malfunction of Near Focus ad-
justment.
Adjustment order
Screen display
Equipment required: Chart
Chart
12
1cm
Camera
Confirm the indication
on the screen.
Finished normally.
Finished abnormally.
Check that Far Focus Adjustment (Page 5-3) is finished normally.
Place the camera in front of the Chart. (Fig. 5-2-4)
Press the (Shutter) button halfway down, then Auto Focus Adjustment (Near Focus Adjustment) starts.
In case of the adjustment is finished normally,
the adjustment completion indication appears
on the screen. (Fig. 5-2-5)
After the adjustment has been successfully
completed, touch the Menu key to return to the
initial screen (adjustment mode screen).
In case of the adjustment is finished abnormally,
the following indication appears on the screen.
(Fig. 5-2-6)
In this case, confirm the adjusting environment
and readjust.
5-2. CAMERA SECTION ADJUSTMENTS
5-2-1. Auto Focus Adjustment
(1) Far Focus Adjustment
Note:
 
When using the Flange back adjustment jig, take care of the following points:
•  For the illumination, use a light source such as an incandescent lamp or inverter type fluorescent light free from flickering.
•  Do not make an adjustment in the environment where fluorescent lamp flickering occurs even if the illuminance can be ensured with the room illumination only.
Use an incandescent lamp or inverter type fluorescent light at a place free from the influence of room illumination.
1)  Install the Flange back adjustment jig so that the distance between 
it and the front of lens of camera is 3cm or less.
Note:  Take care not to hit the Flange back adjustment jig when extend-
ing the lens.
2)  Make the height of Flange back adjustment jig and the camera equal.
3)  Check that the center of chart meets the center of shot image screen. 
Color temperature = 5000 ± 300K
Luminance: LV9 to 11
Be sure not to turn off the power during adjusting.
The adjustment finished normally.
Left Near ADJ
Left Far OK OOO
ADJ OK Pre S1 For Next ADJ
Fig. 5-2-2
The adjustment is complete.
The adjustment is finished abnormally.
Left Far NG XXX
ADJ NG Pre S1 ReADJ
Fig. 5-2-3
Malfunction of Far Focus adjust-
ment
Adjustment order
Screen display
Equipment required: Flange back adjustment jig
Flange back adjustment jig
3cm or less
Camera
Check that the camera is on the adjustment mode.
* For the setting procedure of the adjustment mode, refer to “5-1-4. Setting the Adjustment Mode” (Page 5-3).
In case of the adjustment is finished abnormally,
the following indication appears on the screen.
(Fig. 5-2-3)
In this case, confirm the adjusting environment
and readjust.
In case of the adjustment is finished normally,
the adjustment completion indication appears
on the screen. (Fig. 5-2-2)
The adjustment will proceed to “Near Focus
Adjustment”, do not execute any key operation.
Confirm the indication
on the screen.
Finished normally.
Finished abnormally.
Place the camera in front of the Flange back adjustment jig. (Fig. 5-2-1)
Touch the Up key, then Auto Focus Adjustment (Far Focus Adjustment) starts.
 Fig. 
5-2-1
Fig. 5-2-4
Page of 8
Display

Download Sony MHS-TS22 (serv.man2) Service Manual (Repair Manual)

Here you can read online and download Sony MHS-TS22 (serv.man2) Service Manual in PDF. MHS-TS22 (serv.man2) service manual will guide through the process and help you recover, restore, fix, disassemble and repair Sony MHS-TS22 (serv.man2) Movie. Information contained in service manuals typically includes schematics / circuit diagrams, wiring diagrams, block diagrams, printed wiring boards, exploded views, parts list, disassembly / assembly, pcb.