HDR-PJ260, HDR-PJ260E, HDR-PJ260V, HDR-PJ260VE, HDR-XR260V, HDR-XR260VE - Sony Movie Service Manual (repair manual). Page 9

1-6

HDR-PJ260/PJ260E/PJ260V/PJ260VE/XR260E/XR260V/XR260VE_L2

Order

AdjustBlock

AdjustCode

Procedure

1

Start the Adjust Manual in the Adjust Station and execute the [Measure to E:62:11/12] on the 
[SERVICE] tab.

2

Check if the shift lens moves while setting the order 1.
If the shift lens does not move, replace the lens block (Note).
When the shift lens moved, proceed to the order 3.

3

While setting the order 1, measure with an oscilloscope the output voltage of C5526 and C5527 in 
the periphery of IC5501 on the LD-279 board to check the output voltage varies.

4

If the output voltage does not vary, replace the lens block (Note).
When the output voltage varied, proceed to the order 5.

5

Turn the power OFF.

6

While measuring with an oscilloscope the output voltage of R5505 in the periphery of IC5501 on the 
LD-279 board, turn the power ON to check that the output voltage immediately after the power on 
change as shown in Fig. 2.

7

If the output voltage change as shown in Fig. 2, replace the lens block(Note).
If it does not change as shown in Fig. 2, inspect the camera control circuit (IC1301 of VC-653 board 
and IC5501 of LD-279 board) periphery.

Note:  When the lens block was replaced, start the Adjust Manual in the Adjust Station and execute the necessary adjustment items.
 

After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the handheld operation.

Order

AdjustBlock

AdjustCode

Procedure

1

Start the Adjust Manual in the Adjust Station and execute the [Measure to E:62:11/12] on the [SER-
VICE] tab.

2

Check if the shift lens moves while setting the order 1.
If the shift lens does not move, replace the lens block (Note).
When the shift lens moved, proceed to the order 3.

3

While setting the order 1, measure with an oscilloscope the output voltage of C5528 and C5529 in 
the periphery of IC5501 on the LD-279 board to check the output voltage varies.

4

If the output voltage does not vary, replace the lens block (Note).
When the output voltage varied, proceed to the order 5.

5

Turn the power OFF.

6

While measuring with an oscilloscope the output voltage of R5505 in the periphery
of IC5501 on the LD-279 board, turn the power ON to check that the output voltage
immediately after the power on change as shown in Fig. 2.

7

If the output voltage change as shown in Fig. 2, replace the lens block(Note).
If it does not change as shown in Fig. 2, inspect the camera control circuit (IC1301 of VC-653 board 
and IC5501 of LD-279 board) periphery.

Note:  When the lens block was replaced, start the Adjust Manual in the Adjust Station and execute the necessary adjustment items.
 

After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the handheld operation.

Order

Procedure

1

Turn the power ON.

2

Confirm the connections of flexible flat cables and connectors between the lens block and LD-279 board.

3

In case of no malfunction of connections, replace the lens block with new one (Note) . When the error has occurred in spite of the lens 
replacement, replace LD-279 board with new one.

Note:  When the lens block was replaced, start the Adjust Manual in the Adjust Station and execute the necessary adjustment items.

After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the handheld operation.

After a part of set was replaced or after the set was assembled, check the reception of GPS signal.

Bring your camcorder to an open area, and set the GPS to ON (

 appears on the LCD screen). Your camcorder starts trying to triangulate. When 

your camcorder triangulates successfully, it will record the location information at the time movies and photos were recorded. 

• The indicator changes according to the strength of GPS signal reception.

• It may take a while before the camcorder starts triangulating.

To return the display of the unit to “A message appears asking you to confirm whether you agree with the terms of the license agreement of the map
data,” make settings according to the instructions on the SERVICE tab in the Adjustment Manual.

If you import GPS Assist Data from your computer to your camcorder using the supplied software “PlayMemories Home,” the time it takes the cam-
corder to acquire your location information can be shortened.
Connect the camcorder to a computer that is connected to the Internet. The GPS Assist Data will be updated automatically.

Do not factory check LD-279 board (PJ260/PJ260E/PJ260V/PJ260VE) in which Map Data is installed.
The Map data is erased when the factory check is done.

Do not factory check the HDD (XR260V/XR260VE) in which Map Data is installed.
The Map Data is erased when the factory check is done.

The changed portions from
Ver. 1.0 are shown in blue.