Read Sony HDR-PJ260 / HDR-PJ260E / HDR-PJ260V / HDR-PJ260VE / HDR-XR260V / HDR-XR260VE Service Manual online
HDR-PJ260/PJ260E/PJ260V/PJ260VE/XR260E/XR260V/XR260VE_L2
1-7E
1-11.
NOTE ON REPLACING PROJECTOR UNIT (PJ260/PJ260E/PJ260V/PJ260VE)
Refer to the following flowchart when repairing or inspecting the projector’s projection function.
If you have received an indication on the projector’s projection function from the customer, check defective part according to the following flow-
chart.
When a defective part has been clarified, repair the projector according to the check result.
chart.
When a defective part has been clarified, repair the projector according to the check result.
Note 1: The projector unit (copper plate in particular) becomes hot after it is used.
When replacing a part of the projector unit, wait until it is cooled down.
Wipe the lens gently with a soft cloth such as a cleaning cloth or glass cleaning cloth.
Note 2: Stubborn stains may be removed with a soft cloth such as a cleaning cloth or glass cleaning cloth lightly dampened with water.
Never use a solvent such as alcohol, benzene or thinner; acid, alkaline or abrasive detergent; or a chemical cleaning cloth, as they will damage the lens sur-
face.
face.
Projector problem checking procedure (other than indication on brightness)
Indicated defective
projector received
Measure brightness.
( 2)
Yes
No
OK
OK
NG
NG
OK
NG
A
B
Indication on
brightness
Inspect projector
LED.
( 1)
1 Refer to the ADJUST tab of Adjust Manual.
2 Refer to the SERVICE tab of Adjust Manual.
2 Refer to the SERVICE tab of Adjust Manual.
Inspect projector
LED.
( 1)
END
-
-
-
-
-
-
-
Replace projector unit (light emitting block). (*1)
Replace PJ board. (*1)
Replace both projector unit (light emitting block)
and PJ board. (*1)
Replace PJ board. (*1)
Replace both projector unit (light emitting block)
and PJ board. (*1)
Projector Data Input
Fixed value input
Enter the number on the label attached to the unit.
Serial number input
LD40
Enter the number on the label attached to the unit.
Serial number input
LD40
Syywwnnnnn
Enter the red part.
Projector problem checking procedure (indication on brightness)
Yes
No
OK
NG
OK
NG
OK
NG
A
B
Indicated defective
projector received
Measure brightness.
( 2)
Measure brightness.
( 2)
Indication on
brightness
Inspect projector
LED.
( 1)
1 Refer to the ADJUST tab of Adjust Manual.
2 Refer to the SERVICE tab of Adjust Manual.
2 Refer to the SERVICE tab of Adjust Manual.
END
-
-
-
-
-
-
-
Replace projector unit (light emitting block). (*1)
Replace PJ board. (*1)
Replace both projector unit (light emitting block)
and PJ board. (*1)
Replace PJ board. (*1)
Replace both projector unit (light emitting block)
and PJ board. (*1)
Projector Data Input
Fixed value input
Enter the number on the label attached to the unit.
Serial number input
LD40
Enter the number on the label attached to the unit.
Serial number input
LD40
Syywwnnnnn
Enter the red part.
The changed portions from
Ver. 1.0 are shown in blue.
Ver. 1.0 are shown in blue.
Ver. 1.1 2012.01
Click on the first or last page to see other HDR-PJ260 / HDR-PJ260E / HDR-PJ260V / HDR-PJ260VE / HDR-XR260V / HDR-XR260VE service manuals if exist.