Read Sony HDR-PJ260 / HDR-PJ260E / HDR-PJ260V / HDR-PJ260VE / HDR-XR260V / HDR-XR260VE Service Manual online
1-5
HDR-PJ260/PJ260E/PJ260V/PJ260VE/XR260E/XR260V/XR260VE_L2
Self-diagnosis Code
Symptom/State
Correction
Repaired by:
Block
Function
Detailed
Code
E
6
2
2
0
Abnormality of thermistor.
Refer to [
1-7
-4. E : 62 : 20 (Abnormality of Thermistor) Occurred].
E
9
1
0
1
Abnormality when flash is being charged.
Turn power off and turn power on again.
E
9
1
0
2
Abnormality of LED Video light.
Turn power off and turn power on again.
E
9
1
0
3
Abnormality of LED Video light Tempera-
ture detection.
Turn power off and turn power on again.
E
9
2
0
1
Battery current value goes over the max
discharge current
Check the remaining battery power because this symptom maybe
depended on the remaining battery level, and confirm whether or
not the symptom is occurred after replacing the battery. If the symp-
tom is still occurred, overhaul inspection is needed. Check each
output of DC/DC converter (IC4301 on the VC-653 board) with
connected the DC JACK (J901) on the VC-653 board.
(The minimum connection to periphery)
E
9
4
0
0
Fault of writing or erasing the flash mem-
ory
IM Model:
Inspect the flash memory (IC8101 on the LD-279 board).
E
9
4
0
1
Internal flash memory fault
IM Model:
Inspect the flash memory (IC8101 on the LD-279 board).
E
9
4
0
2
BGM data error
Check the CPU (IC1301 on the VC-652 board).
E
9
5
0
0
GPS hardware error
GPS Model:
Check whether the FFC-254 flexible flat cable is broken,and check
whether it is inserted imperfectly.
If there is no problem the flexible board, inspect or replacement of
the GP-037 board.
E
9
6
0
0
Map area mount error
HDD Model:
Inspect or replacement of the HDD.
IM Model:
Inspect or replacement of the LD-279 board.
E
9
7
0
0
Projector hardware error
Turn power off and turn power on again.
Note 3: When the lens block was replaced, start the Adjust Manual in the Adjust Station and execute the necessary adjustment items.
After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the handheld operation.
*
*
*
1-7.
METHOD OF COPING WITH SHIFT LENS ERROR
LD-279 BOARD (SIDE A)
IC5501
R5505
C5526
C5529
C5528
C5527
Fig. 1
Measurement points on the VC-652 board
about 330 msec
Note: The length of low section will vary a little depending on the conditions.
Fig. 2
Change in output voltage of R5505 on the LD-279 board
1-7
-1. E : 62 : 02 [Abnormality of IC for Steadyshot] Occurred
Order
Procedure
1
Turn the power OFF.
2
While measuring with an oscilloscope the output voltage of R5505 in the periphery of IC5501 on the LD-279 board, turn the power ON
to check that the output voltage immediately after the power on change as shown in Fig. 2.
to check that the output voltage immediately after the power on change as shown in Fig. 2.
3
If the output voltage change as shown in Fig. 2, replace the lens block (Note). If it does not change as shown in Fig. 2, inspect the camera
control circuit (IC1301 of VC-653 board) periphery.
control circuit (IC1301 of VC-653 board) periphery.
Note: When the lens block was replaced, start the Adjust Manual in the Adjust Station and execute the necessary adjustment items.
After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the handheld operation.
The changed portions from
Ver. 1.0 are shown in blue.
Ver. 1.0 are shown in blue.
Ver. 1.1 2012.01
Click on the first or last page to see other HDR-PJ260 / HDR-PJ260E / HDR-PJ260V / HDR-PJ260VE / HDR-XR260V / HDR-XR260VE service manuals if exist.