Read Sony HDR-CX400E / HDR-CX410VE / HDR-CX430V / HDR-CX430VE / HDR-CX510E / HDR-PJ420E / HDR-PJ420VE / HDR-PJ430 / HDR-PJ430E / HDR-PJ430V / HDR-PJ430VE / HDR-PJ510E (serv.man2) Service Manual online
1-8
HDR-CX400E/CX410VE/CX430V/CX430VE/CX510E/PJ420E/PJ420VE/PJ430/PJ430E/PJ430V/PJ430VE/PJ510E_L2
– ENGLISH –
1-10. FRONT ORNAMENT REPLACING METHOD
Lens Cap
Note: A protective Lens Cap is attached to each new service
Lens Block.
Carry out replacement work with this Lens Cap attached.
Removal
(1) Disconnect the three connectors and peel off the Adhesive Parts
of the Motor A Flexible Board, Motor B Flexible Board, and the
FP-2126 Flexible Board.
FP-2126 Flexible Board.
TO
P
FR
ONT
Adhesive part
Adhesive part
Adhesive part
Connector
Connectors
FP-2125 Flexible
Board
Board
FP-2126 Flexible
Board
Board
Flexible Board of the Motor B
Flexible Board of
the Motor A
the Motor A
(2) Remove the seven screws and remove the Sheet Metal (C) and
the Edge of Mechanical Rubber while detaching the two bosses,
and then peel off the Adhesive Part of the FP-2125 Flexible
Board.
and then peel off the Adhesive Part of the FP-2125 Flexible
Board.
TO
P
FRONT
Screws
Screws
Mecha Stopper Rubber
Screw
Screw
Screw
Boss
Boss
Adhesive part
FP-2125
Flexible Board
Flexible Board
Sheet Metal (C)
(3) Peel off the Adhesive Part of the FP-2118 Flexible Board.
TOP
FRONT
Adhesive part
FP-2118
Flexible Board
Flexible Board
(4) Remove the five screws and remove the Frame (F-SUB-A),
Frame (F-SUB-B), and Ball Bearing while detaching the four
bosses and the shaft.
bosses and the shaft.
TO
P
FRONT
Screw
Screw
Screws
Boss
Boss
Boss
Bosses
Shaft
FP-2118 Flexible Board
Motor B
Frame (F-Sub-B),
Ball Bearing
Ball Bearing
Frame (F-Sub-A)
(5) Remove the three screws and remove the Motor B.
Screws
Motor B
FR
ONT
TOP
(6) Disconnect the connector and remove the FP-2118 Flexible
Board and the Radiation Sheet while detaching the four bosses.
FR
ONT
TOP
TOP
Bosses
Adhesive
part
part
Adhesive
part
part
Boss
FP-2118
Flexible Board
Flexible Board
FP-2118 Flexible Board
Connector
Connector
CM Radiation Sheet
(7) Remove the six screws and remove the Frame (E-SUB-A), Frame
(E-SUB-B), Ball Bearing while detaching the six bosses and the
shaft.
shaft.
FRONT
TO
P
Screws
Screws
Boss
Boss
Shaft
Hole
Frame (E-Sub-A),
Ball Bearing
Ball Bearing
Frame (E-Sub-B)
(8) Peel off the Adhesive Part of the Motor A Flexible Board while
detaching the two bosses.
Adhesive part
Flexible Board of
the Motor A
the Motor A
Bosses
FRONT
TOP
Click on the first or last page to see other HDR-CX400E / HDR-CX410VE / HDR-CX430V / HDR-CX430VE / HDR-CX510E / HDR-PJ420E / HDR-PJ420VE / HDR-PJ430 / HDR-PJ430E / HDR-PJ430V / HDR-PJ430VE / HDR-PJ510E (serv.man2) service manuals if exist.