Read Sony HDR-CX400E / HDR-CX410VE / HDR-CX430V / HDR-CX430VE / HDR-CX510E / HDR-PJ420E / HDR-PJ420VE / HDR-PJ430 / HDR-PJ430E / HDR-PJ430V / HDR-PJ430VE / HDR-PJ510E (serv.man2) Service Manual online
1-10
HDR-CX400E/CX410VE/CX430V/CX430VE/CX510E/PJ420E/PJ420VE/PJ430/PJ430E/PJ430V/PJ430VE/PJ510E_L2
– ENGLISH –
Installation
(1) While installing the two bosses and the claw, install the Front Or-
nament.
TOP
FRONT
Front Ornament
Boss
Boss
Claw
(2) While installing the two bosses, install the Sheet Metal D and
tighten two screws.
Tightening torque = 0.12 ± 0.02N · m (1.2 ± 0.2kg f · cm)
TOP
FRONT
Screws
Sheet Metal D
Bosses
1
2
(3) While installing the two bosses, stick the Adhesive Part of the
FP-2126 Flexible Board.
If the adhesive force is lowered, cut the Adhesive Sheet as shown
in the figure in the frame and then stick it.
in the figure in the frame and then stick it.
TOP
FR
ONT
Adhesive part
Adhesive part
FP-2126 Flexible Board
FP-2126 Flexible Board
Sheet Metal A
Bosses
Shape and sticking position of Adhesive Sheet
(4) Connect the connector and install the Sheet Metal A and the FP-
2126 Flexible Board while attaching the six bosses.
Tighten three screws in the order shown in the figure below.
Screw (A)
Screw (A)
Tightening torque = 0.18 ± 0.02N · m (1.8 ± 0.2kg f · cm)
Screw (B)
Screw (B)
Tightening torque = 0.12 ± 0.02N · m (1.2 ± 0.2kg f · cm)
TOP
FRONT
TOP
Screw
(B)
(B)
Screw
(A)
(A)
Screw
(A)
(A)
Connector
Lens
Flexible Board
Flexible Board
Lens Flexible Board
FP-2126
Flexible Board
Flexible Board
FP-2126 Flexible Board
Sheet Metal A
Bosses
Bosses
1
2
3
(5) Set the Plate of the Motor A in the state shown in the figure and
install the Motor A matching it with the two bosses on the Sheet
Metal A, and then tighten three screws in the order shown in the
figure below.
Metal A, and then tighten three screws in the order shown in the
figure below.
Screw
(A)
Tightening torque = 0.12 ± 0.02N · m (1.2 ± 0.2kg f · cm)
Screw
(B)
Tightening torque = 0.18 ± 0.02N · m (1.8 ± 0.2kg f · cm)
FR
ON
T
TO
P
Screws
(A)
(A)
Sheet Metal A
Screws
(B)
(B)
Motor A
Boss
Boss
Screw
(B)
(B)
1
2
3
(6) Attach the Edge of Mechanical Rubber to the Sheet Metal B and
install the Sheet Metal B while matching it with the two bosses.
Tighten three screws in the order shown in the figure below.
Tightening torque = 0.18 ± 0.02N · m (1.8 ± 0.2kg f · cm)
Screws
Sheet Metal B
Boss
Boss
Mecha Stop Rubber
FRON
T
TO
P
1
2
3
Click on the first or last page to see other HDR-CX400E / HDR-CX410VE / HDR-CX430V / HDR-CX430VE / HDR-CX510E / HDR-PJ420E / HDR-PJ420VE / HDR-PJ430 / HDR-PJ430E / HDR-PJ430V / HDR-PJ430VE / HDR-PJ510E (serv.man2) service manuals if exist.