Read Sony SAL1650 Service Manual online
2-5
SAL1650 (DT 16-50 / F2.8) (DT 16-50mm F2.8 SSM)
HELP06
Grease (FT-210): 7-640-018-91
1. Apply the grease (FT-210) to the indicated portion of AF linkage ring.
Apply the grease
(G-116)
(G-116)
AF Linkage Barrel
HELP07
Grease (G-85): J-6082-626-A
Grease (FT-210): 7-640-018-91
Grease (FT-210): 7-640-018-91
1. Apply the grease (G-85) and the grease (FT-210) to the indicated portion of rotary barrel assy.
Apply the grease
(FT-210)
(FT-210)
Apply the grease (G-85)
(all circumferences)
(all circumferences)
Rotary Barrel Assy
Rotary Barrel Assy
HELP08
Grease (G-48): J-6082-669-A
Grease (FT-210): 7-640-018-91
Grease (FT-210): 7-640-018-91
1. Apply the grease (G-48) and the grease (FT-210) to the indicated portion of AF linkage ring.
Apply the grease (FT-210)
(all circumferences)
(all circumferences)
Apply the grease (G-48)
(all circumferences)
(all circumferences)
MF Linkage Barrel
HELP09
Bond (B-10) : J-6082-612-A
1. Install the rotor (SSM assembly) and 3 pieces of stopper pin.
2. Install the stator (SSM assembly), nylon sheet, resin ring, fine same, rubber pressure plate, pressure plate and SSM wave washer
3. Tighten 3 bayonet screws and apply the adhesive bond (B-10) to the screw heads (3 locations).
2. Install the stator (SSM assembly), nylon sheet, resin ring, fine same, rubber pressure plate, pressure plate and SSM wave washer
3. Tighten 3 bayonet screws and apply the adhesive bond (B-10) to the screw heads (3 locations).
Note 1:
Never touch the slip surface of stator (SSM assembly) and resin surface (black coated surface) of rotor (stator set).
Note 2:
When installing the stator (SSM assembly), place the flexible board (stator) and flexible board (relay board) as shown in the
figure.
Note 3:
Install the resin ring, facing the concave side up and the convex side down.
Note 4:
Install the SSM wave washer and pressure plate, facing their concave sides down and their convex sides up.
Note 5:
Be careful for their valley folds not to overlay on the flexible board (stator).
AF Linkage
Barrel
Barrel
Rubber Tube
Stator
(SSM Assy)
(SSM Assy)
Nylon Sheet
Resin Ring
Resin Ring
Convex Side
Convex Side
Concave Side
Concave Side
Note 1:
Never touch the slip surface of
Stator (SSM Assy) and
resin surface of Rotor (SSM Assy)
(black coated surface)
Stator (SSM Assy) and
resin surface of Rotor (SSM Assy)
(black coated surface)
Note 2
Note 3
Note 4
Note 5
Rubber Pressure
Plate
Plate
Pressurizing Plate
SSM Wave Washer
SSM Wave Washer
Mountain Part
Valley Part
Flexible Board (Stator)
SSM Wave Washer,
Pressurizing Plate
Pressurizing Plate
Bayonet
Screws
Screws
Stopper
Stopper
Stopper
Stopper
Fine Sames
Rotor
(SSM Assy)
(SSM Assy)
Flexible Board
(Stator)
(Stator)
Note 2
Cutout of the Middle Barrel Assy
NG
OK
Apply the bond (B-40)
Click on the first or last page to see other SAL1650 service manuals if exist.