Read Sony DSC-G3 (serv.man3) Service Manual online
6-25
DSC-G3_ADJ
10-3. Preparation when the lens is replaced
Note down the PITCH/YAW and FN data on the replacement lens for
repair.
repair.
Adjustment Block
11
Adjustment Page
61
Adjustment Address
0E10, 0E11, 0E07
Note:
The PITCH/YAW and FN data of lens is written only re-
pair parts.
pair parts.
Preparation:
1) Read the PITCH data written on repair parts, and named this
1) Read the PITCH data written on repair parts, and named this
as L
1
.
2) Read the YAW data written on repair parts, and named this as
L
2
.
3) Read the FN data written on repair parts, and named this as
Fpy.
Fig. 6-1-23
10-4. Angular Velocity Sensor Sensitivity Adjustment
[Adjusting method]
1) Click the [Start] button of Camera Adjustment 9, and the fol-
1) Click the [Start] button of Camera Adjustment 9, and the fol-
lowing screen will appear.
The buttons on this screen provide the following functions.
[Read] button: Reads and displays the previous data (Dp, Dy
[Read] button: Reads and displays the previous data (Dp, Dy
and Fpy
*1
) from the SY-211 board.
*1: The Fpy box is displayed, when you give a check to the
check box at lower left of “Input the PITCH/YAW and FN
data”.
data”.
[Save] button: Saves the previous data (Dp, Dy and Fpy) in
the PC as a file.
[Load] button: Loads and displays the previous data (Dp, Dy
and Fpy) from the file saved in the PC.
• Default file name is as follows:
2) Input the previous data (Dp, Dy and Fpy
*1
) into screen.
If the previous data cannot be read, give a check to the checkbox
at lower left of screen.
*1: The Fpy box is displayed, when you give a check to the
at lower left of screen.
*1: The Fpy box is displayed, when you give a check to the
check box at lower left of “Input the PITCH/YAW and FN
data”.
data”.
3) Input the sensitivity of respective sensors (S
501
, S
502
) read at
“Preparation” into the screen.
4) Input the PITCH/YAW and FN data of lens (L
1
, L
2
and Fpy)
read at “Preparation” into the screen.
If the lens was not replaced, give a check to the checkbox at
the lower left of the screen.
If the lens was not replaced, give a check to the checkbox at
the lower left of the screen.
Note:
In order to get the correct value for the adjustment, it is
necessary to input a decimal point (“period” or
“comma”) as same format as windows setting because
“Numeric Value Format” depend on the language.
(F:123 456 789,00, GB:123,456,789.00,
D:123.456.789,00)
“Numeric Value Format” setting is available in “Con-
trol Panel”-“Regional and Language Options”.
necessary to input a decimal point (“period” or
“comma”) as same format as windows setting because
“Numeric Value Format” depend on the language.
(F:123 456 789,00, GB:123,456,789.00,
D:123.456.789,00)
“Numeric Value Format” setting is available in “Con-
trol Panel”-“Regional and Language Options”.
5) Click the [OK] button, and the adjustment data is then calcu-
lated from the sensor sensitivity value and the calculation re-
sult is written to the memory in the camera.
sult is written to the memory in the camera.
6) Upon successful completion of the data writing, the following
screen will appear. Check that the steady shot function oper-
ates normally.
ates normally.
YAW data
t
L
2
PITCH/YAW Data
PITCH data
t
L
1
P.PP / Y.YY
FN Data
FN data
t
Fpy
XX
FN
L1/L2
DSC-G3_D
p
D
y
DT_xxxxxxxx_yyyymmdd.dat
Date
USB serial number
Data name
USB serial number
Data name
Click on the first or last page to see other DSC-G3 (serv.man3) service manuals if exist.