HCD-SHAKE100, HCD-SHAKE99 - Sony Audio Service Manual (repair manual). Page 18

 

To check the emergency history, please follow the following 
procedure.

1.  From the Top Menu of Remocon Diagnosis Menu, select 

“3. Emergency History” by pressing the [3] button on the 
remote commander. The following screen appears on the on-
screen display.

2.  You can check the total time when the laser is turned on 

during playback of DVD and CD from the above menu. The 
maximum time, which can be displayed are 999h 59min.

3.  You can check the error code of latest 10 emergency history 

from the above menu. To view the previous or next page of 
emergency history, press the [.] button or [>] button 
on the remote commander. The error code consists of

The meaning of error code is as below:
01: Communication error (No reply from syscon)
02: Syscon hung up
03: Power OFF request when syscon hung up
19: Thermal shutdown
24: MoveSledHome error
25: Mechanical move error (5 Changer)
26: Mechanical move stack error
30: DC motor adjustment error
31: DPD offset adjustment error
32: TE balance adjustment error
33: TE sensor adjustment error
34: TE loop gain adjustment error
35: FE loop gain adjustment error
36: Bad jitter after adjustment
40: Focus NG
42: Focus layer jump NG
51: Spindle stop error
52: Open kick spindle error
60: Focus on error
61: Seek fail error
62: Read Q data/ID error
70: Lead in data read fail
71: TOC read time out (CD)
80: Can’t buffering
81: Unknown media type

Emg. History Check

1.  01  05  04  04

Laser Hours

CD

999h

59min

DVD

999h

59min

00  92  46  00

00  00  00  00

00  00  23  45

2.  02  02  01  01

00  A9  4B  00

00  00  00  00

00  00  23  45

Next   Next Page

Prev   Prev Page

O  Return to Top Menu

Example of Error code

1.  01  05  04  04

00  92  46  00

00  00  00  00

00  00  23  45

 

In order to execute IOP measurement, the following standard 
procedures must be followed.

1.  From the Top Menu of Remocon Diagnosis Menu, select 

“2. Drive Manual Operation” by pressing the [2] button on 
the remote commander. The following screen appears on the 
onscreen display.

2.  Select “3. Manual Adjustment” by pressing the [3] button on 

the remote commander. The following screen appears on the 
on-screen display.

3.  Select “6. Iop:” by pressing the [6] button on the remote 

commander.

4.  Wait until a hexadecimal number appears in the on-screen 

display as below:

5. Convert data from hexadecimal to decimal by using 

conversion table.

6. Please 

fi nd the label on the rear of the BU (Base Unit).

 

The default IOP value is written in the label.

7.  Subtract between these two values.
8.  If the remainder is smaller than 93 (decimal), then it is OK.
 

However if the value is higher than 93, then the BU is defective 
and need to be change.

9.  Press the [RETURN] button on the remote commander to 

return to previous menu.

10.  Press the [0] button on the remote commander to return to the 

Top Menu of Remocon Diagnosis Menu.

11.  Press the [\/1] button to turn off the system.

 

Drive Manual Operation

1. Servo Control
2. Track/Layer Jump
3. Manual Adjustment
4. Mecha test mode
5. MIRR time Adjust
0. Return to Top Menu

 

Manual Adjust

1. Track Balance Adjust:
2. Track Gain Adjust:
3. Focus Balance Adjust:
4. Focus Gain Adjust:
5. Eg Boost Adjust:
6. Iop:
7. TRV. Level:
8. S curve (FE) Level:
9. RFL (PI) Level:
0. MIRR Time:

O

 

o Change Value

RETURN  Return to previous menu

Manual Adjust

1. Track Balance Adjust:
2. Track Gain Adjust:
3. Focus Balance Adjust:
4. Focus Gain Adjust:
5. Eg Boost Adjust:
6. Iop. ED
7. TRV. Level:
8. S curve (FE) Level:
9. RFL (PI) Level:
0. MIRR Time:

O

 

o Change Value

RETURN  Return to previous menu