Read Sony BDV-IS1000 / HT-IS100 / SA-WIS100 / SS-IS15 Service Manual online
SERVICE MANUAL
Sony Corporation
Audio&Video Business Group
Published by Sony Techno Create Corporation
SA-WIS100/SS-IS15
SPECIFICATIONS
SA-WIS100
ACTIVE SUBWOOFER
SS-IS15
SPEAKER SYSTEM
9-889-129-04
2008K05-1
©
2008.11
US Model
Canadian Model
AEP Model
UK Model
Australian Model
Argentina Model
SA-WIS100/SS-IS15
Saudi Arabia Model
Singapore Model
SS-IS15
Ver. 1.3 2008.11
• SA-WIS100 is the amplifi er, HDMI, tuner, video
and active subwoofer section in HT-IS100.
• SS-IS15 is the front/center/surround speakers
in HT-IS100/BDV-IS1000.
Note: IR-R100 (Remote commander receiver)
is installed in SS-IS15 (center speaker for
HT-IS100 only).
HT-IS100 only).
Photo: SA-WIS100
Photo: SS-IS15 (center speaker with IR-R100 for HT-IS100 only)
This system incorporates Dolby* Digital and Pro Logic Surround and the DTS** Digital Surround System.
* Manufactured under license from Dolby Laboratories.
“Dolby”, “Pro Logic”, and the double-D symbol are trademarks of Dolby Laboratories.
**Manufactured under license under U.S. Patent #'s: 5,451,942; 5,956,674; 5,974,380; 5,978,762; 6,487,535 & other U.S. and worldwide patents issued & pending. DTS and DTS Digital Surround are
registered trademarks and the DTS logos and Symbol are trademarks of DTS, Inc. © 1996-2007 DTS, Inc. All Rights Reserved.
* Manufactured under license from Dolby Laboratories.
“Dolby”, “Pro Logic”, and the double-D symbol are trademarks of Dolby Laboratories.
**Manufactured under license under U.S. Patent #'s: 5,451,942; 5,956,674; 5,974,380; 5,978,762; 6,487,535 & other U.S. and worldwide patents issued & pending. DTS and DTS Digital Surround are
registered trademarks and the DTS logos and Symbol are trademarks of DTS, Inc. © 1996-2007 DTS, Inc. All Rights Reserved.
This system incorporates High-Definition Multimedia Interface (HDMI™) technology.
HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC.
HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC.
“BRAVIA” is a trademark of Sony Corporation.
“S-AIR” and its logo are trademarks of Sony Corporation.
Formats supported by this
system
system
Digital input formats supported by this system
are as follows.
are as follows.
* Linear PCM accepts sampling frequencies of no
more than 96 kHz.
Amplifier section (SA-WIS100)
AUDIO POWER SPECIFICATIONS
AUDIO POWER SPECIFICATIONS
For the U.S.A model
POWER OUTPUT AND TOTAL HARMONIC
DISTORTION:
Front L / Front R:
With 10 ohms loads, both channels driven, from 800 -
20,000 Hz; rated 35 watts per channel minimum RMS
power, with no more than 0.7 % total harmonic
distortion from 250 milli watts to rated output
Subwoofer:
With 4 ohms loads, from 30 - 800 Hz; rated 75 watts per
channel minimum RMS power, with no more than
0.7 % total harmonic distortion from 250 milli watts to
rated output
POWER OUTPUT AND TOTAL HARMONIC
DISTORTION:
Front L / Front R:
With 10 ohms loads, both channels driven, from 800 -
20,000 Hz; rated 35 watts per channel minimum RMS
power, with no more than 0.7 % total harmonic
distortion from 250 milli watts to rated output
Subwoofer:
With 4 ohms loads, from 30 - 800 Hz; rated 75 watts per
channel minimum RMS power, with no more than
0.7 % total harmonic distortion from 250 milli watts to
rated output
Power output (rated)
For Canadian and Argentine models
Front L / Front R (rated): 35 W + 35 W
For Canadian and Argentine models
Front L / Front R (rated): 35 W + 35 W
(at 10 ohms, 1 kHz, 1 %
THD)
THD)
RMS output power (reference)
Front L / Front R*:
Front L / Front R*:
50 W + 50 W
(at 10 ohms, 1 kHz, 10 %
THD)
(at 10 ohms, 1 kHz, 10 %
THD)
Center*:
50 W
(at 10 ohms, 1 kHz, 10 %
THD)
(at 10 ohms, 1 kHz, 10 %
THD)
Surround L / Surround R*: 50 W + 50 W
(at 10 ohms, 1 kHz, 10 %
THD)
THD)
Subwoofer*:
100 W (at 4 ohms, 70 Hz,
10 % THD) + 100 W (at 4
ohms, 500 Hz, 10 % THD)
10 % THD) + 100 W (at 4
ohms, 500 Hz, 10 % THD)
* Depending on the sound field settings and the source,
there may be no sound output.
Inputs (Analog)
VIDEO
VIDEO
Sensitivity: 700 mV
Impedance: 33 kohms
Impedance: 33 kohms
Inputs (Digital)
TV, DVD
TV, DVD
Optical
SAT
Coaxial, optical
HDMI section (SA-WIS100)
Connector
HDMI 19pin-standard
connector
connector
Video inputs/outputs
BD, DVD, SAT:
640 × 480p@60 Hz
720 × [email protected]/60 Hz
1440 × [email protected]/60 Hz
(pixel sent 2 times)
1280 × [email protected]/60 Hz
1920 × [email protected]/
60 Hz
1920 × [email protected]/
60 Hz
720 × 576p@50 Hz
1440 × 576p@50 Hz
(pixel sent 2 times)
640 × 480p@60 Hz
720 × [email protected]/60 Hz
1440 × [email protected]/60 Hz
(pixel sent 2 times)
1280 × [email protected]/60 Hz
1920 × [email protected]/
60 Hz
1920 × [email protected]/
60 Hz
720 × 576p@50 Hz
1440 × 576p@50 Hz
(pixel sent 2 times)
1280 × 720p@50 Hz
1920 × 1080i@50 Hz
1920 × 1080p@50 Hz
1920 × 1080p@24 Hz
1920 × 1080i@50 Hz
1920 × 1080p@50 Hz
1920 × 1080p@24 Hz
Audio inputs
BD, DVD, SAT: Linear
PCM 7.1ch/
Dolby Digital/ DTS
PCM 7.1ch/
Dolby Digital/ DTS
Tuner section (SA-WIS100)
System
PLL quartz-locked digital
synthesizer
synthesizer
FM tuner section
Tuning range
Except AEP and UK models:
Tuning range
Except AEP and UK models:
87.5 – 108.0 MHz
(100 kHz step)
AEP and UK models: 87.5 – 108.0 MHz
(50 kHz step)
Antenna (aerial)
FM wire antenna (aerial)
Antenna (aerial) terminals 75 ohms, unbalanced
Intermediate frequency
Intermediate frequency
10.7 MHz
Format
Supported/Not supported
Dolby Digital
B
DTS
B
Linear PCM (2ch)*
B
Linear PCM (5.1ch,
7.1ch)* (Only on
HDMI)
7.1ch)* (Only on
HDMI)
B
Dolby Digital Plus
×
Dolby True HD
×
×
D
H
-
S
T
D
AM tuner section
Tuning range
Tuning range
Except AEP and UK models:
530 – 1,710 kHz (with the
interval set at 10 kHz)
531 – 1,710 kHz (with the
interval set at 9 kHz)
531 – 1,710 kHz (with the
interval set at 9 kHz)
AEP and UK models: 530 – 1,602kHz (with the
interval set at 9kHz)
Antenna (aerial)
AM loop antenna (aerial)
Intermediate frequency
450 kHz
Video section (SA-WIS100)
Input
VIDEO: 1 Vp-p 75 ohms
Inputs/Outputs
COMPONENT:
Y: 1 Vp-p 75 ohms
P
Y: 1 Vp-p 75 ohms
P
B
/C
B
, P
R
/C
R
: 0.7 Vp-p
75 ohms
Speakers (SS-IS15)
Front/Center/Surround
Front/Center/Surround
Speaker system
Full range speaker system
Speaker unit
35 mm (1
7
/
16
inches)
Rated impedance
10 ohms
Dimensions (approx.)
45 × 55 × 40 mm
(1
(1
13
/
16
× 2
1
/
4
× 1
5
/
8
inches)
(w/h/d)
Mass (approx.)
0.07 kg (3 oz)
Speaker cords
4.5 m × 2, 3 m × 1, 12 m ×
(for HT-IS100)
2 (14.7 ft. × 2, 9.8 ft. × 1,
39.3 ft. × 2)
39.3 ft. × 2)
– Continued on next page –
SA-WIS100/SS-IS15
2
NOTES ON CHIP COMPONENT REPLACEMENT
•
•
Never reuse a disconnected chip component.
•
Notice that the minus side of a tantalum capacitor may be dam-
aged by heat.
aged by heat.
SAFETY CHECK-OUT
After correcting the original service problem, perform the follow-
ing safety check before releasing the set to the customer:
Check the antenna terminals, metal trim, “metallized” knobs,
screws, and all other exposed metal parts for AC leakage.
Check leakage as described below.
After correcting the original service problem, perform the follow-
ing safety check before releasing the set to the customer:
Check the antenna terminals, metal trim, “metallized” knobs,
screws, and all other exposed metal parts for AC leakage.
Check leakage as described below.
LEAKAGE TEST
The AC leakage from any exposed metal part to earth ground and
from all exposed metal parts to any exposed metal part having a
return to chassis, must not exceed 0.5 mA (500 microamperes.).
Leakage current can be measured by any one of three methods.
1. A commercial leakage tester, such as the Simpson 229 or RCA
The AC leakage from any exposed metal part to earth ground and
from all exposed metal parts to any exposed metal part having a
return to chassis, must not exceed 0.5 mA (500 microamperes.).
Leakage current can be measured by any one of three methods.
1. A commercial leakage tester, such as the Simpson 229 or RCA
WT-540A. Follow the manufacturers’ instructions to use these
instruments.
instruments.
2. A battery-operated AC milliammeter. The Data Precision 245
digital multimeter is suitable for this job.
3. Measuring the voltage drop across a resistor by means of a
VOM or battery-operated AC voltmeter. The “limit” indication
is 0.75 V, so analog meters must have an accurate low-voltage
scale. The Simpson 250 and Sanwa SH-63Trd are examples
of a passive VOM that is suitable. Nearly all battery operated
digital multimeters that have a 2 V AC range are suitable. (See
Fig. A)
is 0.75 V, so analog meters must have an accurate low-voltage
scale. The Simpson 250 and Sanwa SH-63Trd are examples
of a passive VOM that is suitable. Nearly all battery operated
digital multimeters that have a 2 V AC range are suitable. (See
Fig. A)
1.5 k
Ω
0.15
μF
AC
voltmeter
(0.75 V)
voltmeter
(0.75 V)
To Exposed Metal
Parts on Set
Parts on Set
Earth Ground
Fig. A. Using an AC voltmeter to check AC leakage.
SAFETY-RELATED COMPONET WARNING!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE
WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS
WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS
WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS
MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 0 SUR
LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES
PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONC-
TIONNEMENT. NE REMPLACER CES COMPOSANTS QUE
PAR DES PIÈCES SONY DONT LES NUMÉROS SONT DON-
NÉS DANS CE MANUEL OU DANS LES SUPPLÉMENTS
PUBLIÉS PAR SONY.
LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES
PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONC-
TIONNEMENT. NE REMPLACER CES COMPOSANTS QUE
PAR DES PIÈCES SONY DONT LES NUMÉROS SONT DON-
NÉS DANS CE MANUEL OU DANS LES SUPPLÉMENTS
PUBLIÉS PAR SONY.
Subwoofer (SA-WIS100)
Remote commander receiver (IR-R100)
Speaker system
2 Way 2 Drivers
Subwoofer speaker system
Subwoofer speaker system
Speaker unit
120 mm + 160 mm (4
3
/
4
inches + 6
3
/
8
inches)
Rated impedance
4 ohms
Dimensions (approx.)
238 × 441 × 434 mm
(9
(9
3
/
8
× 17
3
/
8
× 17
1
/
8
inches) (w/h/d)
Mass (approx.)
14.5 kg (31 lb 16 oz)
Power requirements
US and Canadian models: 120 V AC, 60Hz
Except US and Canadian models:
US and Canadian models: 120 V AC, 60Hz
Except US and Canadian models:
220 – 240 V AC, 50/60 Hz
Power consumption
On: 115 W
Standby mode: 0.3W (when “CTRL: HDMI”
and “S-AIR STBY” are set to “OFF.”)
Standby mode: 0.3W (when “CTRL: HDMI”
and “S-AIR STBY” are set to “OFF.”)
Power output
(DIGITAL MEDIA PORT)DC OUT: 5 V, 700 mA
(DIGITAL MEDIA PORT)DC OUT: 5 V, 700 mA
Design and specifications are subject to change without
notice.
notice.
Dimensions (approx.)
46 × 19 × 45 mm
(1
(1
13
/
16
×
3
/
4
× 1
13
/
16
inches)
(w/h/d)
Mass (approx.)
0.15 kg (6 oz)
SA-WIS100/SS-IS15
3
1.
SERVICING NOTES
............................................. 4
2. GENERAL
.................................................................. 7
3. DISASSEMBLY
3-1. Disassembly (SA-WIS100) ............................................. 8
3-2. Top Panel Block .............................................................. 9
3-3. AMP Block Assy ............................................................. 10
3-4. Top Chassis ..................................................................... 11
3-5. HDMI Board ................................................................... 11
3-6. MAIN Board ................................................................... 12
3-7. Tuner (FM/AM), IR-REPEATER Board ........................ 13
3-8. POWER Board ................................................................ 13
3-9. IO Board ......................................................................... 14
3-10. SPEAKER Board, SAIR Board ...................................... 14
3-2. Top Panel Block .............................................................. 9
3-3. AMP Block Assy ............................................................. 10
3-4. Top Chassis ..................................................................... 11
3-5. HDMI Board ................................................................... 11
3-6. MAIN Board ................................................................... 12
3-7. Tuner (FM/AM), IR-REPEATER Board ........................ 13
3-8. POWER Board ................................................................ 13
3-9. IO Board ......................................................................... 14
3-10. SPEAKER Board, SAIR Board ...................................... 14
4.
TEST MODE
............................................................ 15
5.
ELECTRICAL CHECK
......................................... 16
6. DIAGRAMS
6-1. Block Diagram - MAIN Section - ................................... 17
6-2. Block Diagram - HDMI Section (SA-WIS100) - ........... 18
6-3. Block
6-2. Block Diagram - HDMI Section (SA-WIS100) - ........... 18
6-3. Block
Diagram
- VIDEO, S-AIR Section (SA-WIS100) - ....................... 19
6-4. Block Diagram - AMP Section (SA-WIS100) -.............. 20
6-5. Block Diagram - PANEL, POWER SUPPLY Section
(SA-WIS100)
6-5. Block Diagram - PANEL, POWER SUPPLY Section
(SA-WIS100)
-
................................................................
21
6-6. Schematic
Diagram
- MAIN Board (1/5) (SA-WIS100) - .............................. 23
6-7. Schematic
Diagram
- MAIN Board (2/5) (SA-WIS100) - .............................. 24
6-8. Schematic
Diagram
- MAIN Board (3/5) (SA-WIS100) - .............................. 25
6-9. Schematic
Diagram
- MAIN Board (4/5) (SA-WIS100) - .............................. 26
6-10. Schematic Diagram
- MAIN Board (5/5) (SA-WIS100) - .............................. 27
6-11. Printed Wiring Board
- MAIN Board (Component Side) (SA-WIS100) - ........ 28
6-12. Printed Wiring Board
- MAIN Board (Conductor Side) (SA-WIS100) - .......... 29
6-13. Printed Wiring Board
- HDMI Board (Side A) (SA-WIS100) - ........................ 30
TABLE OF CONTENTS
6-14. Printed Wiring Board
- HDMI Board (Side B) (SA-WIS100) - ........................ 31
6-15. Schematic Diagram
- HDMI Board (1/4) (SA-WIS100) - .............................. 32
6-16. Schematic Diagram
- HDMI Board (2/4) (SA-WIS100) - .............................. 33
6-17. Schematic Diagram
- HDMI Board (3/4) (SA-WIS100) - .............................. 34
6-18. Schematic Diagram
- HDMI Board (4/4) (SA-WIS100) - .............................. 35
6-19. Schematic Diagram
- IO Board (1/2) (SA-WIS100) - ..................................... 36
6-20. Schematic Diagram
- IO Board (2/2) (SA-WIS100) - ..................................... 37
6-21. Printed Wiring Board - IO Board (SA-WIS100) - .......... 38
6-22. Schematic Diagram
6-22. Schematic Diagram
- DISPLAY, KEY Boards (SA-WIS100) - ...................... 39
6-23. Printed Wiring Board
- DISPLAY Board (SA-WIS100) - ................................. 40
6-24. Printed Wiring Board - KEY Board (SA-WIS100) - ...... 41
6-25. Printed Wiring Boards
6-25. Printed Wiring Boards
- S-AIR, IR Section (SA-WIS100) - ............................... 42
6-26. Schematic Diagram
- S-AIR, IR Section (SA-WIS100) - ............................... 43
6-27. Printed Wiring Boards - SPEAKER Section - ................ 44
6-28. Schematic Diagram - SPEAKER Section - .................... 45
6-29. Printed Wiring Board
6-28. Schematic Diagram - SPEAKER Section - .................... 45
6-29. Printed Wiring Board
- POWER Board (SA-WIS100) - .................................... 46
6-30. Schematic Diagram
- POWER Board (SA-WIS100) - .................................... 47
7.
EXPLODED VIEWS
7-1. Overall Section (SA-WIS100) ........................................ 74
7-2. Top Panel Section (SA-WIS100) .................................... 75
7-3. Speaker Cabinet Section (SA-WIS100) .......................... 76
7-4. AMP Block Assy (SA-WIS100) ..................................... 77
7-5. MAIN Board Section (SA-WIS100) ............................... 78
7-6. POWER Board Section (SA-WIS100) ........................... 79
7-7. Chassis
7-2. Top Panel Section (SA-WIS100) .................................... 75
7-3. Speaker Cabinet Section (SA-WIS100) .......................... 76
7-4. AMP Block Assy (SA-WIS100) ..................................... 77
7-5. MAIN Board Section (SA-WIS100) ............................... 78
7-6. POWER Board Section (SA-WIS100) ........................... 79
7-7. Chassis
Section
(SA-WIS100)
........................................ 80
7-8. SS-IS15/IR-R100
............................................................ 81
8.
ELECTRICAL PARTS LIST
.............................. 82
Accessories are given in the last of the electrical parts list.
Note: Refer to page 4, 17, 22, 44, 45, 81, 101
and 102 for information of SS-IS15.
SA-WIS100/SS-IS15
4
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40 °C higher
• Unleaded solder melts at a temperature about 40 °C higher
than ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350 °C.
Caution: The printed pattern (copper foil) may peel away if
about 350 °C.
Caution: The printed pattern (copper foil) may peel away if
the heated tip is applied for too long, so be careful!
• Strong
viscosity
Unleaded solder is more viscous (sticky, less prone to fl ow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
•
Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
also be added to ordinary solder.
NOTE WHEN SA-WIS100 IS OPERATED BY THE RE-
MOTE COMMANDER
When SA-WIS100 is operated by the remoto commander, SS-
IS15 (CENTER SPEAKER) that has installed the remote control
receiver is necessary.
MOTE COMMANDER
When SA-WIS100 is operated by the remoto commander, SS-
IS15 (CENTER SPEAKER) that has installed the remote control
receiver is necessary.
SECTION 1
SERVICING NOTES
NOTE OF WHEN OUTPUT IS CONFIRMED (SS-IS15)
As for SS-IS15, it is designed only for the supplied system model.
Therefore, when it connects with a usual amplifi er and the audio
signal of an excessive low-frequency (800 Hz or less) is input,
there is a possibility that the speaker breaks.
When you confi rm the output with large audio signal input, neces-
sary connect SS-IS15 with the main unit of the supplied system
model.
As for SS-IS15, it is designed only for the supplied system model.
Therefore, when it connects with a usual amplifi er and the audio
signal of an excessive low-frequency (800 Hz or less) is input,
there is a possibility that the speaker breaks.
When you confi rm the output with large audio signal input, neces-
sary connect SS-IS15 with the main unit of the supplied system
model.
NOTE THE IC3511 AND IC3513 ON THE HDMI BOARD
REPLACING (SA-WIS100)
IC3511 and IC3513 on the HDMI board cannot exchange with sin-
gle. When IC3511 and IC3513 on the HDMI board are damaged,
exchange the entire mounted board.
REPLACING (SA-WIS100)
IC3511 and IC3513 on the HDMI board cannot exchange with sin-
gle. When IC3511 and IC3513 on the HDMI board are damaged,
exchange the entire mounted board.
Model
Part No.
US and Canadian models
3-398-647-0[]
AEP and UK models
3-398-649-0[]
Australian model
4-104-461-0[]
Argentina model
4-104-462-0[]
MODEL IDENTIFICATION (SA-WIS100)
Part No.
– Rear side –
Model number label
Ver. 1.2