Read Sony BDV-IS1000 / HT-IS100 / SA-WIS100 / SS-IS15 Service Manual online
SA-WIS100/SS-IS15
4
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40 °C higher
• Unleaded solder melts at a temperature about 40 °C higher
than ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350 °C.
Caution: The printed pattern (copper foil) may peel away if
about 350 °C.
Caution: The printed pattern (copper foil) may peel away if
the heated tip is applied for too long, so be careful!
• Strong
viscosity
Unleaded solder is more viscous (sticky, less prone to fl ow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
•
Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
also be added to ordinary solder.
NOTE WHEN SA-WIS100 IS OPERATED BY THE RE-
MOTE COMMANDER
When SA-WIS100 is operated by the remoto commander, SS-
IS15 (CENTER SPEAKER) that has installed the remote control
receiver is necessary.
MOTE COMMANDER
When SA-WIS100 is operated by the remoto commander, SS-
IS15 (CENTER SPEAKER) that has installed the remote control
receiver is necessary.
SECTION 1
SERVICING NOTES
NOTE OF WHEN OUTPUT IS CONFIRMED (SS-IS15)
As for SS-IS15, it is designed only for the supplied system model.
Therefore, when it connects with a usual amplifi er and the audio
signal of an excessive low-frequency (800 Hz or less) is input,
there is a possibility that the speaker breaks.
When you confi rm the output with large audio signal input, neces-
sary connect SS-IS15 with the main unit of the supplied system
model.
As for SS-IS15, it is designed only for the supplied system model.
Therefore, when it connects with a usual amplifi er and the audio
signal of an excessive low-frequency (800 Hz or less) is input,
there is a possibility that the speaker breaks.
When you confi rm the output with large audio signal input, neces-
sary connect SS-IS15 with the main unit of the supplied system
model.
NOTE THE IC3511 AND IC3513 ON THE HDMI BOARD
REPLACING (SA-WIS100)
IC3511 and IC3513 on the HDMI board cannot exchange with sin-
gle. When IC3511 and IC3513 on the HDMI board are damaged,
exchange the entire mounted board.
REPLACING (SA-WIS100)
IC3511 and IC3513 on the HDMI board cannot exchange with sin-
gle. When IC3511 and IC3513 on the HDMI board are damaged,
exchange the entire mounted board.
Model
Part No.
US and Canadian models
3-398-647-0[]
AEP and UK models
3-398-649-0[]
Australian model
4-104-461-0[]
Argentina model
4-104-462-0[]
MODEL IDENTIFICATION (SA-WIS100)
Part No.
– Rear side –
Model number label
Ver. 1.2
Click on the first or last page to see other BDV-IS1000 / HT-IS100 / SA-WIS100 / SS-IS15 service manuals if exist.