Read Sharp MX-M850 (serv.man36) Service Manual online
MX-M1100 ADJUSTMENTS 6 – 12
3-C
Printer mode lead edge void area
adjustment/Print engine front-rear void
area, rear edge void area adjustment
adjustment/Print engine front-rear void
area, rear edge void area adjustment
This adjustment is needed in the following situations:
* When the resist roller section is disassembled.
* When the LSU is replace or removed.
* U2 trouble has occurred.
* The PCU PWB has been replaced.
* The EEPROM of the PCU PWB has been replaced.
1)
* When the resist roller section is disassembled.
* When the LSU is replace or removed.
* U2 trouble has occurred.
* The PCU PWB has been replaced.
* The EEPROM of the PCU PWB has been replaced.
1)
Enter the Sim. 50-5 mode.
2)
Press [EXECUTE] key.
The adjustment pattern is printed.
Check the adjustment pattern to confirm that the following
items are the standard values.
The adjustment pattern is printed.
Check the adjustment pattern to confirm that the following
items are the standard values.
(Note)
Check by feeding from all the paper feed trays.
If the above conditions are not satisfied or the adjustment
value is set to an optional value, perform the following proce-
dures.
Check by feeding from all the paper feed trays.
If the above conditions are not satisfied or the adjustment
value is set to an optional value, perform the following proce-
dures.
3)
Select the adjustment item with the scroll key.
4)
Enter the adjustment value with 10-key, and press [OK] key or
[EXECUTE] key.
When [EXECUTE] key is pressed, the adjustment pattern is
printed.
When the adjustment value is changed by 1, it is changed by
about 0.1mm.
Repeat procedures 2 thru 4 until the conditions of procedure 2)
are satisfied.
[EXECUTE] key.
When [EXECUTE] key is pressed, the adjustment pattern is
printed.
When the adjustment value is changed by 1, it is changed by
about 0.1mm.
Repeat procedures 2 thru 4 until the conditions of procedure 2)
are satisfied.
A㧦 35
㧧
DEN-C
B㧦 35
㧧
DEN-B
C㧦 35
㧧
FRONT/REAR
D㧦 1
㧧
MULTI COUNT
0
A:
SIMULATION NO.50㧙05
LEAD EDGE ADJUSTMENT VALUE (PRINTER)
35
㨇
1㨪 99 㨉
OK
TEST
CLOSE
E㧦 2
㧧
PAPER㧦CS1
F㧦 1
㧧
DUPLEX㧦NO
EXECUTE
Standard
adjustment value
X
Lead edge void area
3.0
± 1.0mm
Y
Rear edge void area
2.0
± 1.0mm
Z1/Z2
FRONT / REAR void area
2.0
± 2.0mm
Display/Item
Content
Setting range
Default
Remark
A
DEN-C
Printer mode lead edge void quantity
adjustment
adjustment
1-99
35
Adjustment value to fit the print lead edge in the printer mode.
When the adjustment value is decreased by 1, the printer print
start position is shifted to the lead edge in the paper transport
direction by 0.1mm.
When the adjustment value is decreased by 1, the printer print
start position is shifted to the lead edge in the paper transport
direction by 0.1mm.
B
DEN-B
Print rear edge void quantity
adjustment
adjustment
1-99
35
Void quantity generated at the paper rear edge.
When the adjustment value of B (DEN-B) is decreased by 1, the
sub scanning direction print area adjustment value is decreased
in the paper transport direction by 0.1mm.
When the adjustment value of B (DEN-B) is decreased by 1, the
sub scanning direction print area adjustment value is decreased
in the paper transport direction by 0.1mm.
C
FRONT/REAR
FRONT / REAR void quantity
adjustment
adjustment
1-99
35
Adjustment of the void quantity generated at the right and left
edges of paper. When the value is increased, the void quantity
is increased.
edges of paper. When the value is increased, the void quantity
is increased.
D
MULTI COUNT
Print quantity
1-999
1
E
PAPER
MFT
Cassette
select
select
Manual paper feed
1-8
1
2 (CS1)
CS 1
Cassette 1
2
CS 2
Cassette 2
3
CS 3
Cassette 3
4
CS 4
Cassette 4
5
LCC1
LCC1
6
LCC2
LCC2
7
LCC3
LCC3
8
F
DUPLEX
YES
Duplex print
select
select
Yes
0-1
0
1 (NO)
NO
No
1
Click on the first or last page to see other MX-M850 (serv.man36) service manuals if exist.