Read Sharp MX-M850 (serv.man36) Service Manual online
MX-M1100 ADJUSTMENTS 6 – 16
When the right side inclines to the left:
Lower the level of the left side of the rear frame scanner rail.
(When viewed from the rear frame side)
Lower the level of the left side of the rear frame scanner rail.
(When viewed from the rear frame side)
2)
Make a copy of the distortion check test chart, and check for
any distortion on the right side.
Repeat the above procedures until the distortion on the right
side is minimized.
Note:
The right side distortion adjustment and the left side distortion
adjustment affect each other. When, therefore, one of the
adjustments is performed, be sure to check the other distortion
and repeat the adjustment procedures until the both distortions
are minimized.
any distortion on the right side.
Repeat the above procedures until the distortion on the right
side is minimized.
Note:
The right side distortion adjustment and the left side distortion
adjustment affect each other. When, therefore, one of the
adjustments is performed, be sure to check the other distortion
and repeat the adjustment procedures until the both distortions
are minimized.
ADJ 5
Scan image distortion
adjustment (DSPF mode)
adjustment (DSPF mode)
5-A
DSPF level adjustment
This adjustment is required in the following cases:
* When the DSPF section is disassembled.
* The DSPF unit has been replaced.
1)
* When the DSPF section is disassembled.
* The DSPF unit has been replaced.
1)
Check the contact pressures between the four projections (2
on the front side and 2 on the rear side of the DSPF unit) and
the cover top and the glass surface of the document table of
the machine.
on the front side and 2 on the rear side of the DSPF unit) and
the cover top and the glass surface of the document table of
the machine.
(Check procedure)
Insert paper between the projections of the DSPF unit and the
cover top and the glass surface of the document table, and pull
out the paper slowly. Feel and check to confirm that the resis-
tances at the four contacts are the same level.
Allowable range: Front frame side 0mm
Rear frame side 0 - 1mm
* Check the contact pressure with the unit from which the OC
Insert paper between the projections of the DSPF unit and the
cover top and the glass surface of the document table, and pull
out the paper slowly. Feel and check to confirm that the resis-
tances at the four contacts are the same level.
Allowable range: Front frame side 0mm
Rear frame side 0 - 1mm
* Check the contact pressure with the unit from which the OC
mat is removed.
If not, perform the following procedure.
2)
Turn the DSPF unit level adjustment screw on the rear side of
the DSPF unit to adjust the horizontal level (front and rear, left
and right).
the DSPF unit to adjust the horizontal level (front and rear, left
and right).
(Adjustment procedure)
Repeat the above procedures until a satisfactory result is obtained.
When the front frame side
is higher and the rear
frame side is lower
is higher and the rear
frame side is lower
Turn the DSPF rear frame height adjustment
screws R and L clockwise.
screws R and L clockwise.
When the front frame side
is lower and the rear frame
side is higher
is lower and the rear frame
side is higher
Turn the DSPF rear frame height adjustment
screws R and L counterclockwise.
screws R and L counterclockwise.
When the right side is
higher and the left side is
lower
higher and the left side is
lower
Turn the DSPF rear frame height adjustment
screw R counterclockwise.
screw R counterclockwise.
When the right side is
lower and the left side is
higher
lower and the left side is
higher
Turn the DSPF rear frame height adjustment
screw L counterclockwise.
screw L counterclockwise.
Click on the first or last page to see other MX-M850 (serv.man36) service manuals if exist.