Read Sharp MX-M850 (serv.man36) Service Manual online
MX-M1100 ADJUSTMENTS 6 – 10
When [EXECUTE] key is pressed during the adjustment oper-
ation, the operation is terminated and [EXECUTE] key returns
to the normal display.
When setting of the reference toner density control value has
failed, [EE-EU] or [EE-EL] is displayed.
ation, the operation is terminated and [EXECUTE] key returns
to the normal display.
When setting of the reference toner density control value has
failed, [EE-EU] or [EE-EL] is displayed.
<<Error display list (AUTO DEVE ADJUSTMENT)>>
ADJ 3
Print engine image distortion,
image position, image
magnification ratio adjustment
image position, image
magnification ratio adjustment
3-A
Print engine image distortion adjustment
(LSU parallelism adjustment)
(LSU parallelism adjustment)
This adjustment is needed in the following situations:
* The LSU has been replaced or removed.
* Print images are distorted.
This adjustment should be followed by:
* ADJ3C Adjust the print image off-center (print engine section)
1)
* The LSU has been replaced or removed.
* Print images are distorted.
This adjustment should be followed by:
* ADJ3C Adjust the print image off-center (print engine section)
1)
Enter the Sim.64-2 mode.
2)
Set the conditions as shown below.
The paper feed tray with A3 (11
✕ 17) paper in it is selected.
3)
Press [EXECUTE] button.
The grid pattern image is outputted.
The grid pattern image is outputted.
4)
Check the printed grid pattern for distortions.
[Check Method 1]
Compare the front frame side and rear frame side of the
printed paper in terms of the distance between the outer end of
the grid pattern image and the edge of the paper.
No adjustment is needed if the difference between these
dimensions is within 0.5 mm.
[Check Method 1]
Compare the front frame side and rear frame side of the
printed paper in terms of the distance between the outer end of
the grid pattern image and the edge of the paper.
No adjustment is needed if the difference between these
dimensions is within 0.5 mm.
[Check Method 2]
If the right-angle level of the traverse print line is 0.5mm or less
with respect to the longitudinal print line of paper, no adjust-
ment is needed.
If the right-angle level of the traverse print line is 0.5mm or less
with respect to the longitudinal print line of paper, no adjust-
ment is needed.
Carry out the following work if the situation is unsatisfactory.
Error
display
Error name
Detail of error
Remark
EE-EL
EL abnormality
Toner density sensor gain
adjustment voltage is 2.0V
or less.
adjustment voltage is 2.0V
or less.
EE-EU
EU abnormality
Toner density sensor gain
adjustment voltage is 10.6V
or above.
adjustment voltage is 10.6V
or above.
Item
Display Item
Description
Set
value
A
PRINT PATTERN
(1 - 22, 53 - 58, 71 - 78 )
(1 - 22, 53 - 58, 71 - 78 )
Used to specify the print
pattern.
(* For details, refer to the
following descriptions.)
pattern.
(* For details, refer to the
following descriptions.)
5
B
DOT1
(DOT1>=2 IF A : 2, 11)
(DOT1>=2 IF A : 2, 11)
Used to set the print dot
number. (Self print pattern:
for m by n)
number. (Self print pattern:
for m by n)
1
C
DOT2
(DOT2 <= 100 IF A : 59)
(DOT2 <= 100 IF A : 59)
Used to set the empty dot
number. (Self print pattern:
for m by n)
number. (Self print pattern:
for m by n)
254
D
DENSITY
(FIXED ”255” IF A : 9)
(FIXED ”255” IF A : 9)
Used to specify the print
gradation.
gradation.
255
E
RESOLUTION (DPI)
Used to select the
resolution. (600DPI,
1200DPI)
resolution. (600DPI,
1200DPI)
1
F
MULTI COUNT
Number of print
1
A
5
PRINT PATTERN 1 22, 53 -
-
, 71 78
B
1
DOT1 DOT1
2 IF A 2,11
C 254
DOT2 DOT2
100 IF A 59
D 255
DENSITY FIXED”255” IF A 9
0
A:
SIMULATION NO.64-02
SELF PRINT(BW) SERVICE
5
1
82
OK
TEST
EXECUTE
CLOSE
E
1
RESOLUTION(DPI)
F
1
MULTI COUNT
G
8
EXPOSURE 2 8 IF A:14 19
H
2
PAPER CS1
I
1
DUPLEX NO
J
1
PAPER TYPE PLAIN
58
-
G
EXPO
SURE
(2 to 8
IF A :
14 to 19)
SURE
(2 to 8
IF A :
14 to 19)
THROUGH
Used to
specify
the
exposure
mode
specify
the
exposure
mode
No process
(Through)
(Through)
8
(STAN
DARD
DITHER)
CHAR/PIC
Text/Printed
Photo
Photo
CHAR/
PRPIC
PRPIC
Text/
Photograph
Photograph
CHAR
Text
PRINT PIC
Printed Photo
PRINT
PAPER
PAPER
Photograph
MAP
Map
STANDARD
DITHER
DITHER
Dither without
correction
correction
Item
Display Item
Description
Set
value
R
F
b
a
Click on the first or last page to see other MX-M850 (serv.man36) service manuals if exist.