Read Sharp MX-M364N / MX-565N (serv.man4) Service Manual online
MX-M565N ADJUSTMENTS AND SETTINGS 4 – 24
2)
Select the set item L with the scroll key, and enter the value
corresponding to the paper feed tray with A4 (11" x 8.5") paper
in it.
corresponding to the paper feed tray with A4 (11" x 8.5") paper
in it.
3)
Press [EXECUTE] key.
The adjustment pattern is printed.
4)
Measure the distance from the paper lead edge the adjustment
pattern to the image lead edge, and check to confirm that it is
in the standard adjustment value range.
pattern to the image lead edge, and check to confirm that it is
in the standard adjustment value range.
Standard adjustment value: 4.0 ±2.0mm
If the above requirement is not met, do the following steps.
5)
Select the adjustment target of the paper feed mode adjust-
ment item DENC with the scroll key.
ment item DENC with the scroll key.
6)
Change the adjustment value.
Enter the adjustment value and press the [OK] key or the
[EXECUTE] key.
[EXECUTE] key.
When [EXECUTE] key is pressed, the adjustment pattern is
printed. When the adjustment value is increased, the distance
from the paper lead edge to the image lead edge is increased.
When the adjustment value is decreased, the distance is
decreased. When the set value is changed by 1, the distance
is changed by about 0.1mm.
printed. When the adjustment value is increased, the distance
from the paper lead edge to the image lead edge is increased.
When the adjustment value is decreased, the distance is
decreased. When the set value is changed by 1, the distance
is changed by about 0.1mm.
Repeat the procedures 4) - 6) until the condition of 4) is satisfied.
NOTE: To adjust the void area, change the adjustment values of
items B and C.
ADJ 10
Copy image position, image
loss, and void area adjustment
(Manual adjustment)
loss, and void area adjustment
(Manual adjustment)
This manual adjustment is used when the automatic adjustment of
SIM 50-28 cannot obtain a satisfactory result.
SIM 50-28 cannot obtain a satisfactory result.
10-A
Copy image position, image loss, void area
adjustment (Document table mode)
adjustment (Document table mode)
This adjustment is needed in the following situations:
* When the scanner (reading) section is disassembled.
* When the scanner (reading) unit is replaced.
* When the LSU is replaced or removed.
* When the registration roller section is disassembled.
* U2 trouble has occurred.
* The PCU PWB has been replaced.
* The EEPROM of the PCU PWB has been replaced.
* The scanner control PWB has been replaced.
* The EEPROM on the scanner control PWB has been replaced.
NOTE: Before executing this adjustment, be sure to confirm that
the ADJ 3 Print engine image skew, image position, image
magnification ratio, void area adjustments has been com-
pleted normally.
magnification ratio, void area adjustments has been com-
pleted normally.
1)
Place a scale on the document table as shown in the figure
below. Place a scale so that it is in parallel with the scanning
direction and that its lead edge is in contact with the document
guide plate. Place white paper on the document table so that
the scale lead edge can be seen.
below. Place a scale so that it is in parallel with the scanning
direction and that its lead edge is in contact with the document
guide plate. Place white paper on the document table so that
the scale lead edge can be seen.
Item/Display
Content
Setting
range
Default
value
A
DEN-C
Used to adjust the print
lead edge image position.
(PRINTER MODE)
lead edge image position.
(PRINTER MODE)
1 - 99
30
B
DEN-B
Rear edge void area
adjustment
adjustment
1 - 99
30
C
FRONT/REAR
FRONT/REAR void area
adjustment
adjustment
1 - 99
20
D
DENB-MFT
Manual feed rear edge void
area adjustment correction
value
area adjustment correction
value
1 - 99
50
E
DENB-CS1
Tray 1 rear edge void area
adjustment correction value
adjustment correction value
1 - 99
50
F
DENB-CS2
Tray 2 rear edge void area
adjustment correction value
adjustment correction value
1 - 99
50
G
DENB-CS3
Tray 3 rear edge void area
adjustment correction value
adjustment correction value
1 - 99
50
H
DENB-CS4
Tray 4 rear edge void area
adjustment correction value
adjustment correction value
1 - 99
50
I
DENB-LCC
LCC rear edge void aria
adjustment correction value
adjustment correction value
1 - 99
50
J
DENB-ADU
ADU rear edge void aria
adjustment correction value
adjustment correction value
1 - 99
50
K
DENB-HV
Heavy paper rear edge void
area adjustment correction
value
area adjustment correction
value
1 - 99
50
L
MULTI COUNT
Number of print
1 - 999
1
M
PAPER
MFT
Tray
selection
selection
Manual
paper feed
paper feed
1 - 6
1
2 (CS1)
CS1
Tray 1
2
CS2
Tray 2
3
CS3
Tray 3
4
CS4
Tray 4
5
LCC
LCC
6
N
DUPLEX
YES
Duplex print
selection
selection
Yes
0 - 1
0
1 (NO)
NO
No
1
4.0
2.0mm
Click on the first or last page to see other MX-M364N / MX-565N (serv.man4) service manuals if exist.