MX-M364N, MX-565N (serv.man4). Service Manual (Revised January 2016). - Sharp Copying Equipment Service Manual (repair manual). Page 51

MX-M565N  ADJUSTMENTS AND SETTINGS  4 – 21

 

This adjustment must be performed in the following cases:

* When the scan control PWB is replaced.

* When the EEPROM on the scan control PWB is replaced.

* When U2 trouble occurs.

* When the copy magnification ratio is not matched.

* When the DSPF/RSPF is disassembled.

1)

Place the duplex adjustment chart shown below on the docu-
ment tray of the DSPF/RSPF. The adjustment chart is pre-
pared by the following procedures. Use A4 (11" x 8.5") paper,
and put marks on both sides and both surfaces of the paper at
10mm from each edge.

2)

Make a duplex copy at the normal ratio on A4 paper.

3)

Measure the images on the copy paper and the original
images.

4)

Obtain the image magnification ratio according to the following
formula:

Image magnification ratio = Original size / Original size x 100
(%)

Image magnification ratio = 99 / 100 x 100 = 99 (%)

If the image magnification ratio is within the specified range
(100   0.8%), there is no need to perform the adjustment.

If it is not within the specified range, perform the following pro-
cedures.

5)

Enter the SIM 48-1 mode.

* Items A, C, E: When the set value is increased by 1, the 

magnification ratio is increased by 0.02%.

* Items B, D: When the set value is increased by 1, the 

magnification ratio is increased by 0.1%.

* It affects scanning (PC scanning, etc.) as well as copying.

6)

Select an adjustment item with the scroll key.

7)

Enter an image magnification ratio adjustment value with 10-
key, and press [OK] key.

When the adjustment value is increased, the image magnifica-
tion ratio is increased. When the adjustment value is changed
by 1, the image magnification ratio is changed by 0.01%.

Repeat the procedures of 1) - 7) until a satisfactory result is
obtained.

NOTE: When [CLOSE] key is pressed in this simulation mode, the

machine goes into the normal operation mode. Under this
state, copy check can be normally performed. When the
system key is pressed, the machine returns to the simula-
tion mode.

A4 size

10mm

10mm

Paper pass direction

original

copy

10

50

100

150

200

10

50

100

150

200

A

CCD(MAIN)

SCAN main scanning 
magnification ratio 
adjustment (CCD)

1 - 99

50

B

CCD(SUB)

SCAN sub scanning 
magnification ratio 
adjustment (CCD)

1 - 99

50

C

SPF(MAIN)

DSPF document front 
surface magnification ratio 
adjustment (Main scan)

1 - 99

50

D

SPF(SUB)

DSPF document front 
surface magnification ratio 
adjustment (Sub scan)

1 - 99

50

E

SPFB(MAIN)

DSPF document back 
surface magnification ratio 
adjustment (Main scan)

1 - 99

50

SPF (SUB)

Sub scanning direction image magnification ratio 
(Front surface)

SPFB (SUB)

Sub scanning direction image magnification ratio 
(Back surface)

 

　　　S I MU L A TI O N　 　NO . 48 - 0 1

   

 0

T E S T

C L OS E

：  C CD ( MA I N )

：  C C D( S UB )

：  S P F( M AI N )

：  S P F( S UB )

：  S P FB ( MA I N )

M A GN I FI C AT I O N  A DJ U ST M E NT

5 0

A

［  1  ～  9 9  ］

A：    5 0

B：    5 0

C：    5 0

D：    5 0

E：    5 0

O K

10 K EY

1 0K E Y

1 0K E Y

10 K EY

1 0K E Y

1 0K E Y

10 K EY

1 0K E Y

1 0K E Y

10 K EY

1 0K E Y

1 0K E Y

10 K EY

10 K EY

1 0 KE Y

4

5

6

1

2

3

7

8

9

*

0

#

B A C K

S T AR T

EX I T

C LE A R