MX-M364N, MX-565N (serv.man4). Service Manual (Revised January 2016). - Sharp Copying Equipment Service Manual (repair manual). Page 52

MX-M565N  ADJUSTMENTS AND SETTINGS  4 – 22

 

This manual adjustment is used when the automatic adjustment of
SIM 50-28 cannot obtain a satisfactory result.

 

This adjustment is needed in the following situations:

* When the scanner (reading) section is disassembled.

* When the scanner (reading) unit is replaced.

* When a U2 trouble occurs.

* When the scanner control PWB is replaced.

* When the EEPROM on the scanner control PWB is replaced.

1)

Make a copy of the adjustment chart (made by yourself) in the
adjustment mode (document table).

2)

Check the copy image center position.

If A' - B' =  1.0mm, the adjustment is not required.

If the above condition is not satisfied, perform the following
procedures.

3)

Enter the SIM 50-12 mode.

4)

Select the adjustment mode with the scroll key.

5)

Enter the adjustment value with 10-key, and press [OK] key.

The entered value is set. When the set value is increased, the
main scanning print position is shifted to the front side by
0.1mm.

6)

Press [CLOSE] key and shift from the simulation mode to the
copy mode and make a copy. Repeat the procedures of 2) - 6)
until the above condition is satisfied.

 

This adjustment must be performed in the following cases:

* When the scan control PWB is replaced.

* When the EEPROM on the scan control PWB is replaced.

* When the scanner (reading) section is disassembled.

* When the scanner (reading) section is replaced.

* When U2 trouble occurs.

* When the DSPF/RSPF section is disassembled.

* When the DSPF/RSPF unit is replaced.

NOTE: To execute this adjustment, it is required that the ADJ 8A

Scan image off-center adjustment (Document table mode)
must have been properly adjusted.

1)

Prepare the adjustment chart.

Draw a line at the center of the front surface and the back sur-
face of A4 (11" x 8.5") paper in parallel with the paper transport
direction.

2)

Set the adjustment chart to the DSPF/RSPF.

3)

Make a duplex copy in the normal magnification ratio from the
manual paper feed tray, and check the image position on the
front surface and the back surface of the copy paper.

If the difference is within the range of 0   2.7mmm there is no
need to perform the adjustment. If the adjustment is required,
perform the following procedures.

B

A = B

A

B'

A' - B' =  1.0mm

A'

(100%)

 

　　　S I MU L A TI O N　 　NO . 50 - 1 2

   

 0

T E S T

C L OS E

：  O C

：  S P F( S ID E 1 )

：  S P F( S ID E 2 )

O R IG I NA L  C E N TE R  O F FS E T  S E TU P

5 0

A

［  1  ～  9 9  ］

A：    5 0

B：    5 0

C：    5 0

O K

10 K EY

1 0K E Y

1 0K E Y

10 K EY

1 0K E Y

1 0K E Y

10 K EY

1 0K E Y

1 0K E Y

10 K EY

1 0K E Y

1 0K E Y

10 K EY

10 K EY

1 0 KE Y

4

5

6

1

2

3

7

8

9

*

0

#

B A C K

S T AR T

EX I T

C LE A R

Paper transport direction

Front surface

Back surface

Draw a line at the center of the 

front surface and the back surface 

of paper in parallel with the paper 

transport direction.

original

copy

a

b