Read Sharp MX-M364N / MX-565N (serv.man4) Service Manual online
MX-M565N ADJUSTMENTS AND SETTINGS 4 – 10
When the adjustment value is increased, the void area is
increased. When the adjustment value is decreased, the void
area is decreased.
increased. When the adjustment value is decreased, the void
area is decreased.
When the adjustment value is changed by 1, the void area is
changed by 0.1mm.
changed by 0.1mm.
NOTE: The adjustment value and the actual void area are related
as follows:
Adjustment value/10 = Actual void area
NOTE: When the amount of the rear edge void is different between
each paper feed tray, change the adjustment value of item
N, O, P, Q, R, S, T (DENB-XXX) in SIM50-1 and adjust.
N, O, P, Q, R, S, T (DENB-XXX) in SIM50-1 and adjust.
The adjustment item J (DENB) have a effect on the paper
of all paper feed tray.
of all paper feed tray.
That is, adjustment value of item N, O, P, Q, R, S, T
(DENB-XXX) fine adjusts to adjustment item J (DENB) for
each paper tray.
(DENB-XXX) fine adjusts to adjustment item J (DENB) for
each paper tray.
After execution of the above, perform procedures 1) - 4) to check
that the void area is within the specified range.
that the void area is within the specified range.
Though the lead edge void area adjustment value is proper, if the
lead edge void area is not within the specified range, change the
adjustment value of RRCB-XXX (item B, C, D, E, F) of SIM 50-1.
lead edge void area is not within the specified range, change the
adjustment value of RRCB-XXX (item B, C, D, E, F) of SIM 50-1.
Repeat the above procedures until a satisfactory result is obtained.
3-D
Print engine image off-center adjustment
This adjustment is needed in the following situations:
* When the LSU is replaced or removed.
* When a paper tray is replaced.
* When the paper tray section is disassembled.
* When ADJ 3B Print engine image magnification ratio adjustment
(Main scanning direction) is performed.
* When the manual feed tray is replaced.
* When the manual feed tray is disassembled.
* When the duplex section is disassembled.
* When the duplex section is installed or replaced.
* When the large capacity paper feed tray is installed or replaced.
* When the large capacity paper feed tray section is disassembled.
* When the registration roller section is disassembled.
* U2 trouble has occurred.
* The PCU PWB has been replaced.
* The EEPROM of the PCU PWB has been replaced.
(Note)
Before execution of this adjustment, check to insure the following
item.
item.
* Check that the ADJ 3B Print engine image magnification ratio
adjustment (Main scanning direction) has been properly
adjusted.
adjusted.
1)
Enter SIM 50-10 mode.
2)
Use the scroll key to select a paper feed tray which is to be
adjusted. (Items B - H)
adjusted. (Items B - H)
3)
Set A4 (11" x 8.5") paper in the paper feed tray selected in pro-
cedure 2).
cedure 2).
4)
Press [EXECUTE] key.
The adjustment pattern is printed.
5)
Check that the adjustment pattern image is printed in the cor-
rect position.
rect position.
Measure the dimension of the void area in the front and the
rear frame direction of the adjustment pattern, and check that
all the following conditions are satisfied.
rear frame direction of the adjustment pattern, and check that
all the following conditions are satisfied.
N
Sub
scanning
direction
print area
correction
value
scanning
direction
print area
correction
value
DENB-MFT
Manual feed
correction value
correction value
1 - 99
50
O
DENB-CS1
Tray 1 correction
value
value
1 - 99
50
P
DENB-CS2
Tray 2 correction
value
value
1 - 99
50
Q
DENB-CS3
Tray 3 correction
value
value
1 - 99
50
R
DENB-CS4
Tray 4 correction
value
value
1 - 99
50
S
DENB-LCC
LCC correction value
1 - 99
50
T
DENB-ADU
ADU correction value
1 - 99
50
U
DENB-HV
Heavy paper
correction value
correction value
1 - 99
50
Item/Display
Content
Setting
range
Default
value
Item/Display
Content
Setting
range
Default
value
A
BK-MAG
Main scan print
magnification ratio BK
magnification ratio BK
60 - 140
116
B
MAIN-MFT
Print off center adjustment
value (Manual paper feed)
value (Manual paper feed)
1 - 99
60
C
MAIN-CS1
Print off center adjustment
value (Tray 1)
value (Tray 1)
1 - 99
60
D
MAIN-CS2
Print off center adjustment
value (Tray 2)
value (Tray 2)
1 - 99
60
E
MAIN-CS3
Print off center adjustment
value (Tray 3)
value (Tray 3)
1 - 99
60
F
MAIN-CS4
Print off center adjustment
value (Tray 4)
value (Tray 4)
1 - 99
60
G
MAIN-LCC
Print off center adjustment
value (LCC)
value (LCC)
1 - 99
60
H
MAIN-ADU
Print off center adjustment
value (ADU)
NOTE:
value (ADU)
NOTE:
Before execution of this
adjustment check to
insure that the adjustment
items A - G have been
properly adjusted. If not,
this adjustment cannot be
made properly.
adjustment check to
insure that the adjustment
items A - G have been
properly adjusted. If not,
this adjustment cannot be
made properly.
1 - 99
50
I
SUB-MFT
Registration
motor ON
Timing
adjustment
motor ON
Timing
adjustment
Manual
paper feed
paper feed
1 - 99
50
J
SUB-CS1
Standard
tray
tray
1 - 99
50
K
SUB-DSK
DESK
1 - 99
50
L
SUB-LCC
LCC
1 - 99
50
M
SUB-ADU
ADU
1 - 99
50
N
MULTI COUNT
Number of print
1 - 999
1
O
PAPER
MFT
Tray selection
Manual
paper feed
paper feed
1 - 6
1
2
(CS1)
CS1
Tray 1
2
CS2
Tray 2
3
CS3
Tray 3
4
CS4
Tray 4
5
LCC
LCC
6
P
DUPLEX
YES
Duplex print
selection
selection
Yes
0 - 1
0
1 (NO)
NO
No
1
S I MU L A TI O N NO . 50 - 1 0
0
T E S T
C L OS E
： B K- M AG
： M A IN - MF T
： M A IN - CS 1
： M A IN - CS 2
： M A IN - CS 3
： M A IN - CS 4
： M A IN - LC C
： M A IN - AD U
： S UB - MF T
： S U B- D SK
： S U B- C S1
P A PE R C E NT E R O F FS E T S E TU P
11 6
A
［ 6 0 ～ 1 4 0 ］
A： 1 1 6
： S U B- L CC
B： 6 0
C： 6 0
D： 6 0
E： 6 0
F： 6 0
G： 6 0
H： 4 2
I： 6 0
J： 6 0
K： 6 0
L： 6 0
O K
E X EC U TE
10 K E Y
1 0K E Y
1 0K E Y
1 0K E Y
1 0K E Y
1 0K E Y
1 0K E Y
1 0K E Y
1 0K E Y
1 0K E Y
1 0K E Y
1 0K E Y
1 0K E Y
10 K E Y
1 0 KE Y
4
5
6
1
2
3
7
8
9
*
0
#
BA C K
S T AR T
E XI T
C LE A R
Click on the first or last page to see other MX-M364N / MX-565N (serv.man4) service manuals if exist.