MX-M364N, MX-565N (serv.man4). Service Manual (Revised January 2016). - Sharp Copying Equipment Service Manual (repair manual). Page 122

MX-M565N  SIMULATION  5 – 22

 

26-3

Setting

Set the specifications of the auditor

Auditor

Select an item to be set with the touch panel.

(*1) Displayed only when EQUITRAC.

Operation 1: 
Standby during setting time of auto clear. Default is 60 seconds,
which can be changed in the system setting.

Operation 2: 
Auto clear is not made.

Operation 3: 
The display is shifted to the initial screen.

 

26-5

Setting

Set the count mode in A3 (11" x 17") print.

1)

Select an item to be set with scroll key.

2)

Enter the setting value with 10-key 
1 = Count up by 1, 2 = Count up by 2

3)

Press [OK] key.

The set value in step 2) is saved.

 

26-6

Setting

Set the specifications of the destination.

1)

Select an item to be set with the touch panel.

2)

Press [EXECUTE] key.

The selected set content is saved.

 

26-7

Setting

Set the machine ID.

1)

Enter the machine ID with the 10-key.

Max. 30 digits of numerals and alphabetical characters can be
inputted. To select a desired character, press the 10-key
repeatedly. Refer to the following list and enter characters.
Touch the “CONFIRM” section every time a character is
inputted. To modify an inputted character, delete it with
“CLEAR” key and enter the correction character.

BUILT-IN 
AUDITOR

P10

Built-in auditor mode 
(standard mode) operation.

P10

OUTSIDE 
AUDITOR

NONE

No external connection 
vendor is used.

NONE

P VENDOR1

Coin vendor mode 
(Only the copy mode can be 
controlled.)

P VENDOR2

Vendor mode 
communicating with the 
parallel I/F (for DocuLyzer) 
(Japan only)

P VENDOR3

Vendor mode in which 
signals for the intercard 
connected to the PCU are 
used for communication in 
parallel I/F.

VENDOR-EX 
(*1)

Vendor I/F for EQUITRAC

VENDOR-EX 
(MULTI) (*1)

VENDOR-EX + Multi job 
cueing Enable mode

P OTHER

NOT USED

S_VENDOR

Serial vendor mode

DOC ADJ

ON

Support for the auditor in 
document filing print

OFF

OFF

No support for the auditor in 
document filing print

PF ADJ

ON

Continuous printing is 
performed in the duplex print 
mode.
If the remaining money 
expires during continuous 
printing, the sheets in the 
machine are discharged 
without being printed on the 
back surfaces.

OFF

OFF

Continuous printing is not 
performed in the duplex print 
mode. (The remaining 
amount is checked for 
printing every surface in all 
the printing process.)
If the remaining money 
expires during printing, the 
sheet is discharged without 
printing on the back surface.

VENDOR 
MODE (*2)

MODE1

Vendor mode 1

MODE 

3

MODE2

Vendor mode 2

MODE3

Vendor mode 3

COUNTUP 
TIMING

FUSER_IN

When the paper lead edge 
passes the fusing rear 
sensor.

EXIT_

OUT

FUSER_OUT

When the paper rear edge 
passes the fusing rear 
sensor.

EXIT_OUT

When the paper rear edge 
passes the paper exit sensor 
in the main unit, the right tray, 
and the after process unit.

IMS 
CONTROL

ON

There is some restriction in 
the image send mode.

OFF

OFF

There is no restriction in the 
image send mode.

MODE1

Operation 1

Operation 2

Operation 1

MODE2

Operation 1

Operation 1

Operation 1

MODE3

Operation 1

Operation 3

Operation 3

A

TOTAL (B/W)

Total counter

2

B

MAINTE (B/W)

Maintenance counter

2

C

DEV (B/W)

Developer counter

U.S.A.

United States of America

CANADA

Canada

INCH

Inch series, other destinations

JAPAN

Japan

AB_B

AB series (B5 detection), other destinations

EUROPE

Europe

U.K.

United Kingdom

AUS.

Australia

AB_A

AB series (A5 detection), other destinations

CHINA

China