Read Sharp MX-LCX5 Service Manual online
MX-LCX5 REPLACEMENT AND ADJUSTMENT 3 – 3
4th, 5th, and 6th Transport Motors (1), (2), (3)
Remove:
• Left rear cover (see 2.)
[A] Motor unit (connector x 1, Timing belt x 1, screw x 2)
[B] Motor (screw x 2)
LCT Exit Motor (4)
Remove:
• Left rear cover (see 2.)
[C] Motor unit (connector x 1, Timing belt x 1, screw x 3)
[D] Motor (screw x 2)
Remove:
• Left rear cover (see 2.)
[A] Motor unit (connector x 1, Timing belt x 1, screw x 2)
[B] Motor (screw x 2)
LCT Exit Motor (4)
Remove:
• Left rear cover (see 2.)
[C] Motor unit (connector x 1, Timing belt x 1, screw x 3)
[D] Motor (screw x 2)
B. Feed motors/grip motors
Each paper feed unit has a pick-up feed motor (1) and a grip motor
(2). The removal procedure is the same for each feed tray.
1)
(2). The removal procedure is the same for each feed tray.
1)
Remove the left rear cover (see 2.)
2)
Use a small screwdriver to turn the shaft [A] so the pin can slip
out of the keyhole.
out of the keyhole.
Remove:
[B] Motor unit (screw x 4, clamp x 2, connector x 2)
[C] Springs (x 2). First, loosen the screws (x 2) (1), (2).
[D] Paper feed motor (screw x 2, Timing belt x 1)
[E] Grip motor (screw x 2, Timing belt x 1)
Reinstallation
• Attach the tension spring, then tighten the screws (3) to tighten
[B] Motor unit (screw x 4, clamp x 2, connector x 2)
[C] Springs (x 2). First, loosen the screws (x 2) (1), (2).
[D] Paper feed motor (screw x 2, Timing belt x 1)
[E] Grip motor (screw x 2, Timing belt x 1)
Reinstallation
• Attach the tension spring, then tighten the screws (3) to tighten
the belts.
C. Lift motors
4th, 6th Lift Motors
The procedure for removing the 4th and 6th lift motors is the same.
Remove:
• Rear cover. (see 2.)
[A] Motor unit (screw x 2, connector x 1)
[B] 4th (or 6th) lift motor (screw x 4, Clip x 1, Coupling x 1, Spring x
1)
5th Lift Motor
• Rear cover. (see 2.)
[C] Motor unit (screw x 4, connector x 1)
[D] 5th lift motor (screw x 2, Clip x 1, Coupling x 1, Spring x 1)
The procedure for removing the 4th and 6th lift motors is the same.
Remove:
• Rear cover. (see 2.)
[A] Motor unit (screw x 2, connector x 1)
[B] 4th (or 6th) lift motor (screw x 4, Clip x 1, Coupling x 1, Spring x
1)
5th Lift Motor
• Rear cover. (see 2.)
[C] Motor unit (screw x 4, connector x 1)
[D] 5th lift motor (screw x 2, Clip x 1, Coupling x 1, Spring x 1)
(4)
[C]
[D]
(1)
(2)
[A]
[B]
[C]
[D]
(1)
(2)
[E]
[A]
[B]
[C]
[D]
Click on the first or last page to see other MX-LCX5 service manuals if exist.