MX-C301, MX-C301W (serv.man5). Service Manual (Revised May 2016). - Sharp Copying Equipment Service Manual (repair manual). Page 122

MX-C301  SIMULATION  6 – 5

44

1

Used to set each correction operation function in the image forming (process) section.

Image process (Photoconductor/ 
Developing/Transfer/Cleaning)

2

Used to adjust the sensitivity of the image density sensor (registration sensor).

Process

4

Used to set the conditions of the high density process control operation.

Process

6

Used to execute the high density process control forcibly.

Process

9

Used to display the result data of the high density process control operation.

Image process (Photoconductor/ 
Developing/Transfer/Cleaning)

12

Used to display the operation data of the high density process control and the image density sensor 
(registration sensor).

Image process (Photoconductor/
Developing)

14

Used to display the output level of the temperature and humidity sensor.

Process (OPC drum, 
development)/Fusing/LSU

15

Used to set the OPC drum idle rotation.

Developing system

21

Used to set the half tone process control target.

Process

22

Used to display the toner patch density level in the half tone process control operation.

Process

24

Used to display the correction target and the correction level in the half tone process control operation.

Process

25

Used to set the calculating conditions of the correction value for the half tone process control.

Process

26

Used to execute the half tone process control compulsorily.

Process

27

Used to clear the correction data of the half tone process control.

Process

28

Used to set the process control execution conditions.

Process

29

Used to set the operating conditions of the process control during a job.

Process

31

Used to adjust the OPC drum phase. (Manual adjustment)

Process

37

Used to set the development bias correction level in the continuous printing operation.

43

Used to display the identification information of the developing unit.

Developing system

62

Used to set the calibration data of the color image sensor (image registration sensor F).

46

1

Used to adjust the copy density in the color copy mode.

2

Used to adjust the copy density in the monochrome copy mode.

4

Used to adjust the density in the color image send mode.

5

Used to adjust the density in the monochrome image send mode.

8

Used to adjust the image send mode color balance RGB.

9

Used to adjust the scan image density.

10

Used to adjust the copy color balance and the gamma (for each color copy mode).

16

Used to adjust the monochrome copy density and the gamma (for each monochrome copy mode).

19

Used to set the operating conditions for the density scanning (exposure) of monochrome auto copy mode 
documents.

21

Copy color balance adjustment (Manual adjustment)

23

Used to set the density correction of copy high density section (High density tone gap supported).

24

Color balance adjustment (Auto adjustment)

25

Used to adjust the copy color balance. (Single color copy mode)

26

Used to reset the single color mode color balance set value to the default.

27

Used to adjust the gamma/density of copy images, texts, and line image edges.

30

Used to adjust the resolution in the sub scanning direction in the copy mode.

32

Used to set the AE reactivity control.

36

Used to adjust the colors in the 2-color copy mode.

37

Used to adjust the color document reproducibility in the monochrome copy mode.

38

Used to adjust the black component amount in the color copy mode.

39

Used to adjust the sharpness of FAX send images.

40

Used to adjust the FAX send image density. (Collective adjustment of all the modes)

41

Used to adjust the FAX send image density. (Normal)

42

Used to adjust the FAX send image density. (Fine)

43

Used to adjust the FAX send image density. (Super Fine)

44

Used to adjust the FAX send image density. (Ultra fine)

45

Used to adjust the FAX send image density. (600dpi).

47

Used to set the compression rate of copy and scan images (JPEG).

51

Used to adjust the gamma for the copy mode heavy paper mode and the image process mode. 
(Manual adjustment)

52

Used to reset the copy color balance adjustment (adjustment for each dither) to the default value. 
(The set values of SIM46-51 and SIM46-54 are set to the default values.)

54

Used to reset the copy color balance adjustment (auto adjustment for each dither).

58

Used to set the copy mode pseudo resolution. (Smoothing process)

59

Used to perform the copy mode pseudo resolution image process adjustment.

60

Used to adjust the sharpness in the color auto copy mode.

61

Used to adjust the area separation recognition level.

62

Used to set the operating conditions of the ACS, the area separation, the background image process, and the 
auto exposure mode.

63

Used to adjust the density in the copy low density section.

65

Used to set the color correction table.

74

Copy color balance adjustment (Auto adjustment)/Printer color balance adjustment (Auto adjustment)

48

1

Used to adjust the scan image magnification ratio (in the main scanning direction and the sub scanning 
direction).

5

Used to correction the scan image magnification ratio (in the sub scanning direction).

Scanner section

6

Used to adjust the rotation speed of each motor.