MX-C301, MX-C301W (serv.man5). Service Manual (Revised May 2016). - Sharp Copying Equipment Service Manual (repair manual). Page 124

MX-C301  SIMULATION  6 – 7

66

1

Used to display the FAX-related soft SW (2 - 150) on the LCD to allow changing the soft SW while checking 
with the LCD.

FAX

2

Used to enter a country code and set the default value for the country code.

FAX

3

Used to check read/write of the EEPROM and the SDRAM on the MODEM controller and display the result.

FAX

4

Used to send the selected signals to the line and the main unit speaker.

FAX

5

Used to send the selected signal to the line and the main unit speaker. (Send level: Soft SW setting) 
(For the kinds of send signals, refer to SIM66-04.)

FAX

6

Used to print the confidential registration check table (BOX NO., BOX name, passcode. (If there is no 
confidential registration, no print is made.)

FAX

7

Used to output all image data saved in the image memory of FAX part.

FAX

8

Used to send the selected sound messages to the line and the speaker.

FAX

9

Used to send the selected sound message to the line and the speaker. (Send level: Soft SW setting) 
* For details of sound messages, refer to the sound message table of SIM66-08.

FAX

10

Used to clear the FAX image data.

FAX

11

Used to send the selected signal at 300bps to the line and the speaker. 

FAX

12

Used to send the selected signal at 300bps to the line and the speaker. (Send level: Soft SW setting) 
* For the kings of send signals at 300bps, refer to SIM66-11, 300bps send signal table.

FAX

13

Used to execute the dial send test.

FAX

14

Used to execute the dial pulse (10PPS) send test and to adjust the make time.

FAX

15

Used to execute the dial pulse (20PPS) send test and to adjust the make time.

FAX

16

Used to execute the DTFM signal send test and to adjust the send level.

FAX

17

Used to send the DTMF signal to the line and the speaker.

FAX

18

Used to send the DTMF signal to the line and the speaker. (Send level: Soft SW setting)

FAX

21

Used to print the selected items (FAX setting list, software SW list, protocol monitor).

FAX

22

Used to set the handset sound volume. (This simulation can be executed even though the handset setting is 
set to NO. When, however, the handset is not installed, the sound volume cannot be checked.) (Japan model 
only)

FAX

24

Used to clear the FAST save data.

FAX

29

Used to initialize the telephone book data (the one-touch registration table, the FTP/Desktop expansion table, 
the group expansion table, the program registration table, the interface memory box table, the meta data, 
InboundRouting, and the DocumentAdmin table).

FAX

30

Used to display the TEL/LIU status change, The display is highlighted by status change. 

FAX

31

Used to set ON/OFF the port for output to TEL/LIU. 

FAX

32

Used to check the fixed data received from the line and to display the result.

FAX

33

Used to execute detection of various signals with the line connected and to display the detection result. When 
a signal is detected, the display is highlighted.

FAX

34

Used to execute the send test and display the time for sending (receiving) the image data during sending the 
test data on LCD. 

FAX

36

Used to check send and receive data from the MODEM controller to the MFP controller or the data line or the 
command line individually.

FAX

39

Used to check and change the destination setting saved in EEPROM of the FAX BOX.

FAX

42

Used to rewrite the program to power control installed in the FAX BOX.

FAX

43

Used to write the adjustment value into the power control installed in the FAX BOX.

FAX

61

Used to display the FAX-related soft SW (151 - 250) on the LCD to allow changing the soft SW while 
checking with the LCD.

FAX

62

Used to import the FAX receive data into a USB memory in PDF file type.

FAX

67

17

Printer reset

Printer

24

Printer color balance adjustment (Auto adjustment)

Printer

25

Printer color balance adjustment (Manual adjustment)

Printer

26

Used to set the target color balance of the printer mode auto color balance adjustment.

Printer

27

Used to set the service target of the printer mode auto color balance adjustment.

Printer

28

Used to set the default of the service target of the printer mode auto color balance adjustment.

Printer

31

Used to clear the calibration value.

Printer

33

Used to change the gamma of the printer screen.

Printer

34

Used to set the density correction in the printer high density section. (Support for the high density section 
tone gap)

Printer

36

Used to adjust the density in the low density section.

Printer

41

Used to set the threshold value for the printing judgement in the black color of the black and white printing or 
the selected color.  

Printer

42

Used to change the gradation by increasing or decreasing the amount of the black color in the black and 
white printing or the selected color.  

Printer

43

Used to adjust the color balance of the black and white printing finely.

Printer

45

Used to adjust the printer image filter and trapping.

Printer

52

Used to reset the printer color balance adjustment (adjustment for each dither) to the default value. (The set 
values of SIM67-33 are set to the default values.)

54

Printer color balance adjustment (Automatic adjustment for each dither )

Printer