Read Sharp MX-B382 (serv.man6) Service Manual online
MX-B382/B402 SIMULATION 5 – 57
Item A: When the set value is increased, the BK image magnification ratio in the main scanning direction is increased. When the set value is
decreased, the image magnification ratio is decreased.
Item B - G: When the adjustment value is increased, it is shifted to the rear frame side. When the adjustment value is decreased, it is shifted to
the front frame side.
Item B - G: 1 step = 0.1mm change
decreased, the image magnification ratio is decreased.
Item B - G: When the adjustment value is increased, it is shifted to the rear frame side. When the adjustment value is decreased, it is shifted to
the front frame side.
Item B - G: 1 step = 0.1mm change
50-12
Purpose
Adjustment
Function (Purpose) Used to perform the scan image off-center
position adjustment. (The adjustment is
made separately for each scan mode.)
made separately for each scan mode.)
Section
Operation/Procedure
1)
1)
Select an adjustment target item with [
] [] key.
2)
Enter the set value with 10-key.
3)
Press [OK] key. (The set value is saved.)
When the adjustment value is increased, the image position is
shifted to the rear frame side. When the adjustment value is
decreased, it is shifted to the front frame side.
1step = 0.1mm
shifted to the rear frame side. When the adjustment value is
decreased, it is shifted to the front frame side.
1step = 0.1mm
50-27
Purpose
Adjustment
Function (Purpose) Used to perform the image loss adjustment
of scanned images in the FAX or image
send mode.
send mode.
Section
Operation/Procedure
1)
1)
Select a target adjustment mode.
2)
Select an adjustment target item with [
] [] key on the touch
panel.
3)
Enter the set value with 10-key.
4)
Press [OK] key. (The set value is saved.)
Item/Display
Content
Setting range
Default
value
NOTE
A
BK-MAG
Main scan print magnification ratio BK
60 - 140
100
Adjustment Item List
B
MAIN-MFT
Print off center adjustment value
(Manual paper feed)
(Manual paper feed)
1 - 99
65
C
MAIN-CS1
Print off center adjustment value (Tray 1)
1 - 99
65
D
MAIN-CS2
Print off center adjustment value (Tray 2)
1 - 99
50
E
MAIN-CS3
Print off center adjustment value (Tray 3)
1 - 99
50
F
MAIN-CS4
Print off center adjustment value (Tray 4)
1 - 99
50
G
MAIN-ADU
Print off center adjustment value (Duplex)
(NOTE) If the adjustment items A - F are
not properly adjusted, this adjustment
cannot be executed properly.
(NOTE) If the adjustment items A - F are
not properly adjusted, this adjustment
cannot be executed properly.
1 - 99
50
Adjustment Item List
H
SUB-MFT
Resist motor ON
timing adjustment
timing adjustment
Manual paper feed
1 - 99
60
I
SUB-CS1
Standard cassette
1 - 99
60
J
SUB-DSK
DESK 1
-
99
50
K
SUB-ADU
ADU
1 - 99
50
L
MULTI COUNT
Number of print
1 - 999
1
Adjustment pattern print conditions setting
M
PAPER
MFT
Tray selection
Manual paper feed
1 - 5
1
2 (CS1)
CS1
Tray 1
2
CS2
Tray 2
3
CS3
Tray 3
4
CS4
Tray 4
5
N
DUPLEX
YES
Duplex print
selection
selection
Yes
0 - 1
0
1 (NO)
NO
No
1
Item/Display
Content
Setting
range
Default
value
A
OC
Document table image off-
center adjustment
center adjustment
1 - 99
50
B
SPF(SIDE1)
RSPF front surface image
off-center adjustment
off-center adjustment
1 - 99
50
C
SPF(SIDE2)
RSPF back surface image
off-center adjustment
off-center adjustment
1 - 99
50
Item/Display
Content
Setting
range
Default
value
FAX
send
send
A
Image
loss
amount
setting
OC
loss
amount
setting
OC
LEAD_EDGE
(OC)
(OC)
OC lead
edge
image loss
amount
setting
edge
image loss
amount
setting
0 - 100
30
(3mm)
B
FRONT
_REAR (OC)
_REAR (OC)
OC side
image loss
amount
setting
image loss
amount
setting
0 - 100
20
(2mm)
C
TRAIL_EDGE
(OC)
(OC)
OC rear
edge
image loss
amount
setting
edge
image loss
amount
setting
0 - 100
20
(2mm)
D
Image
loss
amount
setting
SPF
SIDE1
loss
amount
setting
SPF
SIDE1
LEAD_EDGE
(SPF_SIDE1)
(SPF_SIDE1)
Front
surface
lead edge
image loss
amount
setting
surface
lead edge
image loss
amount
setting
0 - 100
20
(2mm)
E
FRONT
_REAR
(SPF_SIDE1)
_REAR
(SPF_SIDE1)
Front
surface
side image
loss
amount
setting
surface
side image
loss
amount
setting
0 - 100
20
(2mm)
F
TRAIL_EDGE
(SPF_SIDE1)
(SPF_SIDE1)
Front
surface
rear edge
image loss
amount
setting
surface
rear edge
image loss
amount
setting
0 - 100
30
(3mm)
Click on the first or last page to see other MX-B382 (serv.man6) service manuals if exist.