MX-B382 (serv.man6). Service Manual (Revised May 2016). - Sharp Copying Equipment Service Manual (repair manual). Page 120

MX-B382/B402  SIMULATION  5 – 52

 

48-5

Adjustment

Function (Purpose) Used to correction the scan image magnifi-

cation ratio (in the sub scanning direction).

Scanner section

Operation/Procedure
1)

Select a target adjustment item with [

] [] key.

2)

Enter the set value with 10-key.

3)

Press [OK] key.
The set value is saved.

When the image magnification ratio in the sub scanning direction is
adjusted with SIM48-1, and a different magnification ratio is speci-
fied, and the image magnification ratio is not satisfactory, perform
this adjustment.
When there is an error in the image magnification ratio in reduction,
change the adjustment value in the high speed mode. When there
is an error in the image magnification ratio in enlargement, change
the adjustment value in the low speed mode.

 

48-6

Adjustment

Function (Purpose) Used to adjust the rotation speed of each

motor.

Operation/Procedure
1)

Select an adjustment target mode.

2)

Select a target adjustment item with [

] [] key on the touch

panel.

3)

Enter the set value with 10-key.

4)

Press [OK] key.
The set value is saved.

When the adjustment value is increased, the speed is increased,
and vice versa. A change of 1 in the adjustment value corresponds
to a change of about 0.1% in the speed.

NOTE: This must be set to the default unless any change is spe-

cially required.
When the adjustment value is set to a value greatly differ-
ent from the default value, a jam, paper wrinkle, or image
quality trouble may occur.

 

 

49-1

Purpose
Function (Purpose) Used to perform the firmware update.
Section

Operation/Procedure
1)

Save the firmware to the USB memory.

2)

Insert the USB memory into the main unit.

3)

Select a target firmware file for update.

4)

Press [EXECUTE] key.

5)

Press [YES] key.
The selected firmware is updated.
When the operation normally completed, "COMPLETE" is dis-
played. When terminated abnormally, "ERROR" is displayed.

A

CCD (MAIN)

SCAN main scanning 
magnification ratio 
adjustment (CCD)

1 - 99

50

B

CCD (SUB)

SCAN sub scanning 
magnification ratio 
adjustment (CCD)

1 - 99

50

C

SPF (MAIN)

RSPF document front 
surface magnification ratio 
(Main scan)

1 - 99

50

D

SPF (SUB)

RSPF document front 
surface magnification ratio 
(Sub scan)

1 - 99

50

E

SPFB (MAIN)

RSPF document back 
surface magnification ratio 
(Main scan)

1 - 99

50

F

SPFB (SUB)

RSPF document back 
surface magnification ratio 
(Sub scan)

1 - 99

50

A

MR (HI)

Scanner motor (High speed)

1 - 99

50

B

MR(MID)

Scanner motor 
(Reference speed)

1 - 99

50

C

MR(LO)

Scanner motor (Low speed)

1 - 99

50

D

SPF(HI)

Document feed (RSPF) 
motor (High speed)

1 - 99

50

E

SPF(MID)

Document feed (RSPF) 
motor (Reference speed)

1 - 99

50

A

RRM

Resist 
motor 
correction 
value

Mono-

chrome

MONO

1 - 99

52

Heavy 

paper

HEAVY

46

B

DVM_K

Developing 
K motor 
correction 
value

Mono-

chrome

MONO

1 - 99

52

Heavy 

paper

HEAVY

C

FSM

Fusing 
motor 
correction 
value

Mono-

chrome

MONO

1 - 99

60

Heavy 

paper

HEAVY

60

D

PFM

Paper transport motor 
correction value.

MONO

1 - 99

50

E

POM

Paper exit motor 
correction value

MONO

1 - 99

45

F

FUSER 
SETTING

Fusing speed select 
timing

HEAVY

1 - 99

50

G

RRM 
START

RRM speed 
increasing start timing

HEAVY

1 - 255

90

H

RRM END

RRM speed 
increasing end timing

HEAVY

1 - 255

30

CONFIG

Configuration data

ICU (MAIN)

ICU Main section former half

ICU (BOOTM)

ICU Boot section main

ICU (BOOTCN)

ICU Boot section CN

LANGUAGE

Language support data program (General term)

GRAPHIC

Graphic data for L-LCD

SLIST

SLIST data for L-LCD

PCU (BOOT)

PCU Boot section

PCU (MAIN)

PCU Main section

DESK (BOOT)

Desk unit BOOT section

DESK (MAIN)

Desk unit MAIN section

FIN (BOOT)

Inner finisher BOOT section

FIN (MAIN)

Inner finisher MAIN section

SCU (BOOT)

SCU Boot section

SCU (MAIN)

SCU Main section

FAX (BOOT)

FAX1 Boot section

FAX(MAIN)

FAX1 Main section

ESCP_FONT

ESC/P font

PDL_FONT

PDL font

ANIMATION

Animation data