Read Sharp MX-B382 (serv.man6) Service Manual online
MX-B382/B402 SIMULATION 5 – 55
When the adjustment value is increased, the distance from the paper lead edge to the image lead edge is increased. When the adjustment
value is decreased, the distance from the paper lead edge to the image lead edge is decreased.
When the set value is changed by 1, the distance is changed by about 0.1mm.
value is decreased, the distance from the paper lead edge to the image lead edge is decreased.
When the set value is changed by 1, the distance is changed by about 0.1mm.
50-6
Purpose
Adjustment
Function (Purpose) Used to adjust the copy image position and
the image loss. (RSPF mode)
Section
RSPF
Operation/Procedure
1)
1)
Select an adjustment target item with [
] [] key.
2)
Enter the set value with 10-key.
3)
Press [OK] key. (The set value is saved.)
Item/Display
Content
Setting
range
Default
value
NOTE
A
DEN-C
Used to adjust the print
lead edge image
position.
(PRINTER MODE)
lead edge image
position.
(PRINTER MODE)
1 - 99
30
Adjustment value too align the print lead edge for the printer. When the
adjustment value of this item is decreased by 1, the printer print start position
in the paper transport direction is shifted to the lead edge by 0.1mm.
adjustment value of this item is decreased by 1, the printer print start position
in the paper transport direction is shifted to the lead edge by 0.1mm.
B
DEN-B
Rear edge void area
adjustment
adjustment
1 - 99
30
Void amount generated at the paper rear edge. When the adjustment value
of item B (DEN-B) is decreased by 1, the print area adjustment value in the
sub scanning direction for the paper transport direction is decreased by
0.1mm.
of item B (DEN-B) is decreased by 1, the print area adjustment value in the
sub scanning direction for the paper transport direction is decreased by
0.1mm.
C
FRONT/REAR
FRONT/REAR void area
adjustment
adjustment
1 - 99
30
Adjustment of the void amount generated on the left and right edges of paper.
When the adjustment value is increased, the void amount is increased.
When the adjustment value is increased, the void amount is increased.
D
DENB-MFT
Manual feed rear edge
void area adjustment
correction value
void area adjustment
correction value
1 - 99
50
Fine adjustment value of each paper feed source for the adjustment value of
DEN-B
DEN-B
E
DENB-CS1
Tray 1 rear edge void
area adjustment
correction value
area adjustment
correction value
1 - 99
50
F
DENB-CS2
Tray 2 rear edge void
area adjustment
correction value
area adjustment
correction value
1 - 99
50
G
DENB-CS3
Tray 3 rear edge void
area adjustment
correction value
area adjustment
correction value
1 - 99
50
H
DENB-CS4
Tray 4 rear edge void
area adjustment
correction value
area adjustment
correction value
1 - 99
50
I
DENB-ADU
ADU rear edge void aria
adjustment correction
value
adjustment correction
value
1 - 99
50
J
MULTI COUNT
Number of print
1 - 999
1
Adjustment pattern print conditions setting
K
PAPER
MFT
Tray
selection
selection
Manual
paper feed
paper feed
1 - 5
1
2 (CS1)
CS1
Tray 1
2
CS2
Tray 2
3
CS3
Tray 3
4
CS4
Tray 4
5
L
DUPLEX
YES
Duplex
print
selection
selection
Yes
0 - 1
0
1 (NO)
NO
No
1
Item/Display
Content
Setting
range
Default
value
A
SIDE1
Front surface
document scan
position
adjustment
(CCD)
document scan
position
adjustment
(CCD)
1 - 99
50
B
SIDE2
Back surface
document scan
position
adjustment
(CCD)
document scan
position
adjustment
(CCD)
1 - 99
50
C
Image
loss
amount
setting
SIDE1
loss
amount
setting
SIDE1
LEAD_EDGE
(SIDE1)
(SIDE1)
Front surface
lead edge image
loss amount
setting
lead edge image
loss amount
setting
0 - 99
20
D
FRONT_REAR
(SIDE1)
(SIDE1)
Front surface side
image loss
amount setting
image loss
amount setting
0 - 99
20
E
TRAIL_EDGE
(SIDE1)
(SIDE1)
Front surface rear
edge image loss
amount setting
edge image loss
amount setting
0 - 99
30
F
Image
loss
amount
setting
SIDE2
loss
amount
setting
SIDE2
LEAD_EDGE
(SIDE2)
(SIDE2)
Back surface lead
edge image loss
amount setting
edge image loss
amount setting
0 - 99
20
G
FRONT_REAR
(SIDE2)
(SIDE2)
Back surface side
image loss
amount setting
image loss
amount setting
0 - 99
20
H
TRAIL_EDGE
(SIDE2)
(SIDE2)
Back surface rear
edge image loss
amount setting
edge image loss
amount setting
0 - 99
30
I
OFSET_SPF1
SPF front surface
document off-
center adjustment
document off-
center adjustment
1 - 99
50
J
OFSET_SPF2
SPF back surface
document off-
center adjustment
document off-
center adjustment
1 - 99
50
Item/Display
Content
Setting
range
Default
value
Click on the first or last page to see other MX-B382 (serv.man6) service manuals if exist.