Read Sharp MX-B382 (serv.man6) Service Manual online
MX-B382/B402 SIMULATION 5 – 54
50-2
Purpose
Adjustment
Function (Purpose) Used to adjust the copy image position and
the image loss. (This simulation is a simpli-
fied version of SIM 50-1).
fied version of SIM 50-1).
Section
Operation/Procedure
The magnification ratio adjustment in the sub scanning direction
must be executed in advance. (SIM48-01)
1)
The magnification ratio adjustment in the sub scanning direction
must be executed in advance. (SIM48-01)
1)
Set item A (L1) and item B (L2) to 0.
2)
Place a rule on the left edge of the document table, and make
a copy at a magnification ratio of 200%.
a copy at a magnification ratio of 200%.
3)
Measure the length of L1 and L2 on the copied image in the
unit of 0.1mm (referring to the figure below). Enter the adjust-
ment values of L1 x 10 and L2 x 10. Be sure to enter the both
adjustment values of L1 and L2.
L1: Distance from the lead edge of the copied image to 10mm
scale.
L2: Distance from the paper lead edge to the copy image lead
edge.
unit of 0.1mm (referring to the figure below). Enter the adjust-
ment values of L1 x 10 and L2 x 10. Be sure to enter the both
adjustment values of L1 and L2.
L1: Distance from the lead edge of the copied image to 10mm
scale.
L2: Distance from the paper lead edge to the copy image lead
edge.
4)
Press [EXECUTE] key. (The set value is saved.)
5)
Make a copy at the magnification ratio of 100%, and adjust the
lead edge void.
lead edge void.
Same as the adjusted items of SIM50-01 except for A and B.
The values adjusted with A and B are reflected to the document
lead edge reference position (RRC-A) of SIM50-01 and all the
paper lead edge positions (RRCB-**).
All adjustment items: 1 step = 0.1mm change
The values adjusted with A and B are reflected to the document
lead edge reference position (RRC-A) of SIM50-01 and all the
paper lead edge positions (RRCB-**).
All adjustment items: 1 step = 0.1mm change
50-5
Purpose
Adjustment
Function (Purpose) Used to adjust the print lead edge image
position. (PRINTER MODE)
Section
Operation/Procedure
1)
1)
Select a target adjustment item (DEN-C) with [
] [] key.
2)
Enter the adjustment value using the 10-key.
3)
Press [EXECUTE] key.
The set value is saved, and the adjustment check pattern is
printed.
The set value is saved, and the adjustment check pattern is
printed.
4)
Measure the distance from the paper lead edge the adjustment
pattern to the image lead edge, and check to confirm that it is
in the standard adjustment value range.
Standard reference value: 3.0
pattern to the image lead edge, and check to confirm that it is
in the standard adjustment value range.
Standard reference value: 3.0
2.0mm
When the adjustment value is increased, the distance from the
paper lead edge to the image lead edge is increased. When the
adjustment value is decreased, the distanced is decreased.
When the set value is changed by 1, the distance is changed by
about 0.1mm.
paper lead edge to the image lead edge is increased. When the
adjustment value is decreased, the distanced is decreased.
When the set value is changed by 1, the distance is changed by
about 0.1mm.
Item/Display
Description
Setting
range
Default
value
A
Actual
measurem
ent value
measurem
ent value
L1
Distance from the
image lead edge to
the scale of 10mm.
(Platen 400%,
0.1mm increment)
image lead edge to
the scale of 10mm.
(Platen 400%,
0.1mm increment)
0 - 999
-
B
L2
Distance from the
paper lead edge to
the image lead edge
(0.1mm increment)
paper lead edge to
the image lead edge
(0.1mm increment)
0 - 999
0
C
Image loss
area
setting
value
area
setting
value
LEAD
Lead edge image
loss amount setting
(When the
adjustment value is
increased, the image
loss is increased.)
loss amount setting
(When the
adjustment value is
increased, the image
loss is increased.)
0 - 99
30
D
SIDE
Side edge image
loss amount setting
(When the
adjustment value is
increased, the image
loss is increased.)
loss amount setting
(When the
adjustment value is
increased, the image
loss is increased.)
0 - 99
20
Paper lead
edge
edge
L1
L2
200% enlargement copy
Fig. 1
E
Void area
adjustment
adjustment
DENA
Lead edge void area
adjustment (When
the adjustment value
is increased, the void
is increased.)
adjustment (When
the adjustment value
is increased, the void
is increased.)
1 - 99
30
F
DENB
Rear edge void area
adjustment (When
the adjustment value
is increased, the void
is increased.)
adjustment (When
the adjustment value
is increased, the void
is increased.)
1 - 99
30
G
FRONT/
REAR
REAR
FRONT/REAR void
amount adjustment
(When the
adjustment value is
increased, the void is
increased.)
amount adjustment
(When the
adjustment value is
increased, the void is
increased.)
1 - 99
30
Item/Display
Description
Setting
range
Default
value
Click on the first or last page to see other MX-B382 (serv.man6) service manuals if exist.