Read Sharp MX-5500N / MX-6200N / MX-7000N (serv.man46) Service Manual online
MX-7000N SIMULATION 7 – 13
3-10
Purpose
Adjustment
Function (Purpose) Used to adjust the finisher.
Section
Section
Finisher
Operation/Procedure
1)
1)
Select an item corresponding to the adjustment content with
[
[
↑] and [↓] keys on the touch panel.
2)
Enter the adjustment value with 10-key.
3)
Press [OK] key. (The set value is saved.)
<4K finisher>
<4K saddle finisher>
3-30
Purpose
Operation test/Check
Function (Purpose) Used to check the operations of the sen-
sors and detectors in the inserter and the
control circuits.
control circuits.
Section
Inserter
Operation/Procedure
The operating conditions of the sensors and detectors are dis-
played.
Sensors and detectors which are turned on are highlighted.
The operating conditions of the sensors and detectors are dis-
played.
Sensors and detectors which are turned on are highlighted.
3-31
Purpose
Operation test/Check
Function (Purpose) Used to check the operations of the loads
in the inserter and the control circuit.
Section
Inserter
Operation/Procedure
1)
1)
Select a target of the operation check with the touch panel.
2)
Press [EXECUTE] key.
The selected load is operated.
When [EXECUTE] is pressed, the operation is stopped.
The selected load is operated.
When [EXECUTE] is pressed, the operation is stopped.
Item
Display
Item
Set
range
Default
value
A
FRONT
ADJUST
ADJUST
Alignment position
adjustment (front)
adjustment (front)
0 - 20
10
B
STAPLE
REAR
REAR
Staple binding position
adjustment (one position
at the rear)
adjustment (one position
at the rear)
94 - 106
100
C
STAPLE
FRONT
FRONT
Staple binding position
adjustment (one position
in front)
adjustment (one position
in front)
94 - 106
100
D
PUNCH
CENTER
CENTER
Punch center adjustment
30 - 70
50
E
PUNCH HOLE
Punch hole position
adjustment
adjustment
46 - 52
50
Item
Display
Item
Set
range
Default
value
A
SADDLE
POSITION
POSITION
Saddle binding position
adjustment
adjustment
197 - 203
200
B
FOLDING
POSITION
POSITION
Saddle folding position
adjustment
adjustment
192 - 208
200
C
FRONT
ADJUST
ADJUST
Alignment position
adjustment (front)
adjustment (front)
0 - 20
10
D
STAPLE
REAR
REAR
Staple binding position
adjustment (one position
at the rear)
adjustment (one position
at the rear)
94 - 106
100
E
STAPLE
FRONT
FRONT
Staple binding position
adjustment (one position
in front)
adjustment (one position
in front)
94 - 106
100
F
PUNCH
CENTER
CENTER
Punch center adjustment
30 - 70
50
G
PUNCH HOLE
Punch hole position
adjustment
adjustment
46 - 52
50
SIMULATION NO.03-03
TEST
FIN LOAD CHECK
EXECUTE
1/1
CLOSE
FINRPS
FJPM
FJFM
FFM
FAM
FFJM
FRJM
FSM
FTLM1
FTLM2
FFSM
FSWM
FASM
FINRRS
FBRRS
FFDRRS
FBES
FSHC
FAORC
TH_SEN
Inserter sub tray pull-out detection
TS_SEN
Inserter sub tray storage detection
T_SEN
Inserter tray paper length detection
EMP_SEN
Inserter tray empty detection
REG_SEN
Inserter resist detection
TIM_SEN
Inserter timing detection
JCK_SEN
Inserter JAM cover open/close detection
H_SEN
Inserter reverse detection
HI_SEN
Inserter paper exit detection
HYK_SEN
Inserter reverse unit open/close detection
P_ST_SW
Inserter start SW
P_MO_SW
Inserter staple mode select SW
P_PN_SW
Inserter punch select SW
SET_SW
Inserter set SW
K_MOT
Inserter paper feed motor
Y_MOT
Inserter horizontal transport motor
H_MOT
Inserter reverse motor
F_SOL
Inserter flapper solenoid
A : 10
;
FRONT ADJUST
B : 100
;
STAPLE REAR
C : 100
;
STAPLE FRONT
D : 50
;
PUNCH CENTER
A:
SIMULATION NO.03-10
FINISHER ADJUSTMENT
10
0
20
OK
TEST
CLOSE
E : 50
;
PUNCH HOLE
FIN SENSOR CHECK
CLOSE
SIMULATION NO.03-30
TEST
1/1
TH_SEN
TS_SEN
T_SEN
EMP_SEN
REG_SEN
TIM_SEN
JCK_SEN
H_SEN
HI_SEN
HYK_SEN
P_ST_SW
P_MO_SW
P_PN_SW
SET_SW
Click on the first or last page to see other MX-5500N / MX-6200N / MX-7000N (serv.man46) service manuals if exist.