Read Sharp MX-5500N / MX-6200N / MX-7000N (serv.man33) Peripheral online
MX-7000N MX-LCX3 3 – 10
2)
Open the front cabinet of the main unit. Turn ON the power
switch in the front cabinet.
switch in the front cabinet.
3)
Turn ON the power switch on the operation panel.
G. Size setting
1)
Check to insure that the main body is standby state, and press
the [System setting] key on the operation panel.
the [System setting] key on the operation panel.
2)
Menu screen is displayed on the touch panel. Select the
[Paper Tray Settings].
[Paper Tray Settings].
3)
Select the paper size of LCC from contents of [Paper Tray Set-
tings].
tings].
H. Carry out the print off-center adjustment
(1) Adjustment with the simulation
Since the off-center adjustment has been made at shipping, there
is normally no need to adjust. However, if the center is shifted,
carry out the following steps to adjust.
1)
is normally no need to adjust. However, if the center is shifted,
carry out the following steps to adjust.
1)
Set a test chart (document) on the document table properly.
2)
Execute SIM 50-10 (Print off center) by the key operation of
the main unit.
the main unit.
3)
In SIM 50-10, the display is shown as follows to allow setting of
the print off-center adjustment value for each paper feed tray.
the print off-center adjustment value for each paper feed tray.
[When shifted to the front side]
To adjust the print line in the direction A from the paper center as
shown in the figure, increment the number of value.
shown in the figure, increment the number of value.
Then make a copy to check to insure that there is no more shift.
Repeat the procedures until there is no shift.
Repeat the procedures until there is no shift.
[When shifted to the rear side]
To adjust the print line in the direction B from the paper center as
shown in the figure, decrement the number of value.
shown in the figure, decrement the number of value.
Then make a copy to check to insure that there is no more shift.
Repeat the procedures until there is no shift.
* For details of the adjustment and checking procedures, refer to
Repeat the procedures until there is no shift.
* For details of the adjustment and checking procedures, refer to
the "[6] ADJUSTMENT" on the Service Manual.
"ON"
ON
ON
Item
Default
A
BK-MAG
Main scan print magnification ratio BK
100
B
MFT
Print off-center adjustment value
(Manual paper feed)
(Manual paper feed)
50
C
CS1
Print off-center adjustment value
(Tray 1)
(Tray 1)
50
D
CS2
Print off-center adjustment value
(Tray 2)
(Tray 2)
50
E
CS3
Print off-center adjustment value
(Tray 3)
(Tray 3)
50
F
CS4
Print off-center adjustment value
(Tray 4)
(Tray 4)
50
G
LCC
Print off-center adjustment value
(LCC)
(LCC)
50
H
ADU
Print off-center adjustment value (ADU)
50
I
MULTI COUNT
Number of print
1
J
PAPER
MFT
Tray selection
1 : Manual paper feed
2
CS 1
2 : Tray 1
CS 2
3 : Tray 2
CS 3
4 : Tray 3
CS 4
5 : Tray 4
LCC
6 : LCC
K
DUPLEX
YES
Duplex
selection
selection
0 : Selection
1
NO
1 : Unselection
R side
Center line of image (first image)
F side
(Fig. 1)
Direction A
R side
Center line of Image (first image)
F side
(fig. 2)
Direction B
Click on the first or last page to see other MX-5500N / MX-6200N / MX-7000N (serv.man33) service manuals if exist.