Read Sharp AR-M550 (serv.man15) Service Manual online
AR-M550/M620 SIMULATION 8 - 96
Operation/Procedure
When check is completed normally, "OK" is displayed. In case of an
error, "NG" is displayed.
error, "NG" is displayed.
(Display message)
Operation/Procedure
The detected signal is highlighted.
Operation/Procedure
Communication test is performed to measure the time (ms).
Send is made under the following conditions.
Operation/Procedure
1) Select YES/NO of Modem program reload.
2) Press [START] key.
When reload is completed normally, "OK" is displayed. In case of an
error, "CHECK SUM" is displayed.
error, "CHECK SUM" is displayed.
The result of Modem reload is displayed.
Operation/Procedure
1) Enter the number corresponding to the check mode with 10-key.
2) Press [START] key.
When check is completed normally, "OK" is displayed. Incase of an
error, "NG" is displayed.
error, "NG" is displayed.
When check is "repeat," the operation is continued until the result is
NG or [CUSTOM SETTINGS] key is pressed.
NG or [CUSTOM SETTINGS] key is pressed.
66-32
Purpose
Operation test/Check
Function
(Purpose)
(Purpose)
Used to check the receive data (fixed data) from the
line.
line.
Section
FAX
Item
Operation
CHECKING
Checking
OK
Checking completed (OK)
NG
Checking completed (NG)
66-33
Purpose
Operation test/Check
Function
(Purpose)
(Purpose)
Used to check the signal (BUSY TONE/CNG/CED/
FNET/DTMF) detection.
FNET/DTMF) detection.
Section
FAX
Item
Operation
66-34
Purpose
Operation test/Check
Function
(Purpose)
(Purpose)
Used to measure the communication time of test
image data.
image data.
Section
FAX
Item
Operation
Communication means
Memory send
Image quality
Normal text
Density
Light
ECM
ON
Sender record
OFF
SIMULATION 66-32
RECEIVED DATA CHECK.
CHECKING···.(OK or NG)
SIMULATION 66-33
SIGNAL DETECT CHECK.
BUSY TONE
CNG
CED FNET DTMF
SIMULATION 66-34
COMMUNICATION TIME DISPLAY.
* * * * * ms
66-35
Purpose
Setting
Function
(Purpose)
(Purpose)
Modem program reloading (Only when FAX is
installed)
Not used in the market. (For development)
installed)
Not used in the market. (For development)
Section
FAX
Item
Data
1
YES
Modem block reload is cleared.
2
NO
Not reloaded.
COMPLETE
Reload completed
81
Check sum error
82
Write error
83
Delete error
84
Verify error
NG
Due to loader NG
Press [START] key.
After completion of reloading
66-36
Purpose
Operation test/Check
Function
(Purpose)
(Purpose)
Used to check interface between MFPC controller and
MDMC. (Check of the data line or the command line)
MDMC. (Check of the data line or the command line)
Section
FAX
Item
Operation
1
MFPC
←
MDMC
Date line once only
2
MFPC
→
MDMC
Date line once only
3
MFPC
←
MDMC
Data line repeat
4
MFPC
→
MDMC
Data line repeat
5
MFPC
←
MDMC
Command line once only
6
MFPC
→
MDMC
Command line once only
7
MFPC
←
MDMC
Command line repeat
8
MFPC
→
MDMC
Command line repeat
SIMULATION 66-35
MODEM PROGRAM RELOAD.
ARE YOU SURE?
1. YES
2. NO
1
SIMULATION 66-35
MODEM PROGRAM RELOAD.
EXECITOMG···
LOADER··· xxxxx
MODEM···· xxxxx
SIMULATION 66-35
MODEM PROGRAM RELOAD.
LOADER···OK
MODEM····COMPLETE
Click on the first or last page to see other AR-M550 (serv.man15) service manuals if exist.